Anest Iwata GRAVITY SPRAYGUNS Serie Manual De Instrucciones página 5

WS-400 Series2 [BASE & CLEAR] - LS-400 Series2 GRAVITY SPRAY GUNS
EN
4 5
2
Replace the Coin Battery with a new Fit the new Coin battery in its seat
one and dispose the exhausted one and put in place the cover housing
adequately according to the regulations correctly.
in force.
7 8
Place the DPG-1 module in its seat on Align the module to the surface of its
the gun handle and make sure that both housing and secure it on the handle of
magnetic surfaces of the two parts the gun by the magnetic adhere.
match perfectly.
14. MAINTENANCE AND INSPECTION
CAUTION! BEFORE CARRYING OUT MAINTENANCE AND INSPECTION ALWAYS OBSERVE
WARNING INDICATIONS.
NEVER USE SPARE PARTS THAT ARE NOT ANEST IWATA ORIGINALS.
NEVER DAMAGE FLUID NOZZLE TIP, FLUID NEEDLE OR AIR CAP HOLES.
NEVER IMMERSE THE SPRAY GUN COMPLETELY IN LIQUIDS SUCH AS THINNER, GUN CLEANER, SOLVENT OR
OTHER AGRESSIVE LIQUIDS.
15. CLEANING PROCEDURE
THE FLUID PASSAGES OF THE SPRAY GUN, MUST BE CLEANED THOROUGHLY AFTER EACH
USE, ESPECIALLY AFTER USE WITH BI-COMPONENT PAINTS. INCOMPLETE CLEANING CAN
CAUSE DEFECTIVE PATTERN SHAPE.
NEVER SOAK AIR CAP SET (1) IN CLEANER FOR AN EXTENDED PERIOD, EVEN WHEN CLEANING.
NEVER IMMERSE THE DIGITAL PRESSURE GAUGE MODULE DPG-1 IN ANY LIQUIDS EVEN
WHEN CLEANING.
NEVER USE METAL BRUSH OR ABRASIVE PRODUCT TO CLEAN THE GUN.
ALWAYS DISASSEMBLE DIGITAL PRESSURE GAUGE DEVICE FROM SPRAY GUN HANDLE BEFORE CLEANING PROCEDURE
AND BEFORE TO INTRODUCE THE SPRAY GUN IN THE WASHING MACHINE FOR AUTOMATIC WASHING.
8
6
1
3
Put in place in the seat of the cover,
the two fixing bolts and tighten them
by the supplied screwdriver.
9
Check the correct position of the devi-
ce before proceeding with the painting
operations.
WS-400 Series2 [BASE & CLEAR] - LS-400 Series2 GRAVITY SPRAY GUNS
16. MANUAL CLEANING PROCEDURE
Always release air and fluid pressure from the spray gun before proceeding with cleaning procedure.
1
2 Drain remaining paint from spray gun and gravity cup, into a suitable container.
Pour the cleaner into the gravity cup, leave it to act for a few seconds and carry out a preliminary wash to remove any
3
excess of residual paint.
Unscrew the air cap (1) by 2 turns, to allow the atomizing air to do the back flush of the cleaner in the paint passages of
4 the gun. Pull the trigger and make sure that the atomizing air enters into the cup. Repeat the operation many times as
necessary. Clean the paint passages and each section of the gun using the supplied brush soaked in compatible cleaner.
Remove the air cap from the gun body and if it is necessary, immerse it in the cleaner to soften the paint residues
encrusted on the air outlet holes. Once extracted it from the cleaning liquid, proceed to blow the air cap holes with
5
compressed air eliminating the residues of softened product, then proceed with an accurate and delicate cleaning of
all the holes with a soft cleaning needle avoiding scratching the surfaces of the holes.
After having dried each part with an absorbent cloth, and in order to guarantee the perfect performance of the spray
gun it is necessary to lubricate each tightening seat, and each friction zone, with the compatible lubricant included,
6
especially after each cleaning performed in a spray gun washer. It is important to check that the lubricant used does
not contain components that could ruin the quality of the atomization (silicones, etc.)
MAKE SURE THAT THE PH LEVEL OF CLEANER DOES NOT EXCEED THE LIMIT.
PH level: 6.0~8.0 (but only during cleaning).
16.1 WARNING FOR THE CLEANING OF THE GUN BODY SURFACE
DO NOT USE PRODUCT TO PICKLING THE SURFACES.
DO NOT USE PAINT STRIPPERS OR DESCALERS.
DO NOT USE ACID CONTENT CHEMICAL PRODUCTS.
DO NOT USE SOLVENTS, THINNERS OR CLEANING PRODUCTS PRODUCED BY RECYCLED EXHAUST CHEMICAL
PRODUCTS.
DO NOT LEAVE THE GUN IMMERSED IN THE CLEANING OR DEGREASING CHEMICAL PRODUCTS.
USE ANTI-FOG SOLVENTS OR THINNERS.
DRY OR BLOW OUT THE GUNS WITH COMPRESSED AIR AFTER CLEANING TO AVOID CHEMICAL PRODUCT STUCK
THAT AFTER LONG TIME CAN DAMAGE THE SURFACE.
RINSE THE GUN WITH CLEAN SOLVENT ONLY.
DO NOT CLEAN OR POLISH THE GUN SURFACE WITH ABRASIVE PRODUCTS OR PRODUCTS THAT CAN
MECHANICAL DAMAGE THE SURFACES LIKES: ABRASIVE PASTES, METALLIC BRUSHES, POLISHING WHEELS OR
ABRASIVE SPONGES.
CHECK TRHOUGHT THE DATA SHEET THAT CLEANING PRODUCT DOES NOT INCLUDE THE
IMPORTANT:
FOLLOWING COMPONENTS:
• DICHLOROMETHANOL
• AMMONIUM BIFLORIDE
• HYDROGEN PEROXIDE 130 vol.
• NITRIC ACID
• TRIPOTASSIUM HEXACYANOFERRATE
17. WARNING DURING AUTOMATIC WASHING PROCEDURE
WHEN USING AUTOMATIC SPRAY GUN WASHER, ALWAYS FOLLOW THE INSTRUCTION MANUAL
PROVIDED WITH IT.
BEFORE CLEANING, MAKE SURE AIR IS RELEASED FROM AIR PASSAGES.
ONLY USE SUITABLE CLEANER DESIGNED FOR YOUR SPRAY GUN WASHER.
MAKE SURE THAT THE EQUIPMENT IS DRIED IMMEDIATELY AFTER CLEANING.
SECURELY CONNECT GROUND THE GUN WASHER EQUIPMENT, USE OF CLEANER WITH WATER-BASE COATINGS
RESIDUES, IT COULD INCREASE PH LEVEL, ESPECIALLY AFTER SEVERAL WASHINGS. PLEASE, REPLACE THE
CLEANER REGULARLY IN ORDER TO ALWAYS ENSURE THE BEST SPRAY GUN PERFORMANCE.
EN
9