Key Selector Switch And Auxiliary Pushbuttons; Testing; Spare Parts; Disposal - Comunello Automation RAMPART 600 Instrucciones De Uso

5.1.13 KEY SELECTOR SWITCH AND AUXILIARY PUSHBUTTONS

If auxiliary controls are to be wired into the system (e.g. key selector
switches) they can be connected in parallel with the dedicated inputs
(Open-Close command terminals M1-M2 and Stop command terminals
M1-M3).

6 TESTING

Each part of the automation system, e.g. safety edges, photocells,
emergency stop, etc. must be tested; follow the procedures shown in
the instruction manuals supplied with the devices in question. Perform
the following sequence of operations for testing of RAMPART:
• Check that all the prescriptions in this manual have been followed
scrupulously, with special attention to the matters set down in
chapter 1 "General Prescriptions".
• Using the supplied control or stopping devices (key selector switch,
pushbuttons or remotes), perform door opening, closing and
stopping tests and make sure the door responds correctly to the
various commands.
• Check operation of all the system's safety devices (photocells, safety
edges, emergency stop, etc.) one by one.
7 MAINTENANCE
Maintenance must be carried out at regular intervals by qualified
personnel in compliance with the provisions of statutory legislation and
the regulations in force. RAMPART must be serviced at least once every
6 months or after 10.000 operating cycles since the last service.
• Disconnect the operator from all power supplies.
• Check all the moving parts and replace any worn parts.
• Check all parts of the automation system for signs of deterioration.

8 SPARE PARTS

Spare parts can be purchased by contacting technical service.

9 DISPOSAL

At the end of its useful life the automation system must be dismantled
by qualified personnel and the materials must be recycled or disposed
of in compliance with the local legislation in force.

10 WARRANTY

a) In business relationships or in case of products sold for professional
use, this warranty is limited to the repair or replacement of product parts
that FRATELLI COMUNELLO SPA acknowledges as defective, through
equivalent re-manufactured Products (the "Conventional Warranty"); the
warranty does not include the costs necessary for repairing or replacing
the material (e.g. labour costs, rental of equipment etc).
b) The provisions contained in articles 1490 to 1495 of the Italian Civil
Code shall not apply.
c) FRATELLI COMUNELLO SPA warrants the proper operation of the
products within the limits indicated in a) above. Unless otherwise
agreed, the validity of the Conventional Warranty is 24 (twenty-four)
months from the production date, which can be found on the products.
The Warranty shall be effective and binding on COMUNELLO only if the
product has been correctly installed and maintained in accordance with
the installation and safety rules set out in the documentation provided
by COMUNELLO or otherwise available on the website http://www.
comunello.com/corporate/ general_conditions_sales/
d) The warranty does not cover: failures or damage caused by transport;
failures or damage caused by defects in the electrical system of the
buyer and/or by carelessness, negligence, inadequate or abnormal
use of such system; failure or damage due to tampering carried out
by unauthorized personnel or due to incorrect use / installation (in this
regard, system maintenance at least every six months is recommended)
or the use of non-original spare parts; defects caused by chemical
agents and/or atmospheric phenomena. The warranty does not cover
the cost of consumables; in any event, COMUNELLO shall be entitled
to a consideration for the work performed at the Customer, where such
work proves useless as the warranty did not apply or because the
customer had used the Comunello product in a negligent, reckless
or incompetent manner, such that the proper use of the product could
have avoided the work.
e) Implementation terms: unless otherwise agreed, the right to the
Conventional Warranty is exercised by showing a copy of the purchase
document (invoice) to COMUNELLO. Any defect must be notified to
COMUNELLO within the time limit of thirty (30) days from detection of
the defect.
The action must be exercised within the limitation period of 6 (six)
months from detection of the defect. The Product parts for which the
Customer requests application of the Conventional Warranty must be
returned by the Customer to FRATELLI COMUNELLO SPA, Via Cassola
64, 36027 Rosà (VI) Italy.
f) The Customer cannot claim compensation for indirect damage, loss of
profits, loss of production and in any case it cannot claim compensation
for an amount that exceeds the value of the supplied components or
products. All transport costs for Products that have been repaired or to
be repaired, although covered by the Conventional Warranty, shall be
charged to the Customer.
g) No external work carried out by Comunello technical staff is covered
by the Conventional Warranty.
h) Specific amendments to the Conventional Warranty conditions
described herein can be defined by the parties in their commercial
contracts.
i) The Court of Vicenza (Italy) shall be the place of jurisdiction for any
dispute which will be settled according to the Italian laws.
COMUNELLO ®Copyright 2018 - All rights reserved
19