MBM FB74AXS Manual De Uso E Instalación página 47

1. Solid top: T ≤ 250 ° C / Lower
temperature at the hottest point
2. Mijotage: T ≤ 150 ° C / Lower
temperature at the hottest point
Do not obstruct the burner
flange eyelets - see seCT.
IMAGES - REF. t)
Before using the oven for the firs
time, it is advisable to pre-heat it
at the highest setting for 30-40
minutes with the door closed. This
burns any oily residue that could relea-
se unpleasant odours.
LIGHTING OPEN BURNERS - see
SECT. IMAGES - REF. u)
Turn the knob while holding it in the
piezoelectric position (Detail A Fig.1).
Position a flame (match or something
else) on the pilot light and wait for it to
ignite (Fig. 1).
Release the knob after about 20" and
check to make sure the pilot light re-
mains lit.
When the pilot light has been lit, turn
the knob (Detail B Fig.1) to minimum
or maximum to adjust the flame.
HOTPLATE IGNITION - see SECT.
IMAGES - REF. u)
Turn the knob while holding it in the
piezoelectric position (Fig. 2 Detail A),
and simultaneously press the piezoe-
lectric button several times (Fig. 2 De-
tail B) until the pilot light is lit.
Release the knob after about 20" and
check to make sure the pilot light re-
mains lit (Fig. 2).
The pilot light can be seen through
the hole on the panel.
When the pilot light has been lit, turn
the thermostat knob to the desired
temperature (Fig. 2 Detail C).
LIGHTING GAS OVEN - see SECT.
IMAGES - REF. u)
Turn the knob while holding it in the
piezoelectric position (Fig.3 Detail
THE PRESENT MANUAL IS PROPERTY OF THE MANUFACTURER. ANY REPRODUCTION, EVEN PARTIAL, IS PROHIBITED.
INSTRUCTIONS FOR USE
A). Simultaneously press the piezoe-
lectric button several times (Fig.3 De-
tail B) until the pilot light is lit.
Release the knob after about 20" and
check to make sure the pilot light re-
mains lit (Fig.3).
The pilot light can be seen through
the hole on the oven top.
When the pilot light has been lit, turn
the thermostat knob to the desired
temperature (Fig. 3 Detail C).
SWITCHING ELECTRIC OVEN ON -
see SECT. IMAGES - REF. u)
When necessary, plug the ap-
pliance into the appropriate
socket.
Turn the thermostat knob to the desi-
red position (Fig. 4 A -B). The indicator
lights "G" and "H" indicate an opera-
ting phase.
Green indicator light: The indicator
is subordinated to use of the switch-on
knob. Lighting of the indicator signals
the operating phase.
Yellow indicator light: The indicator
is subordinated to use of the thermo-
stat knob. Lighting of the indicator si-
gnals the heating phase.
NEW! ELECTRONIC IGNITION (OP-
TIONAL) / IGNITION OPEN BUR-
NERS - vd. sect. ILL - REF s) /
In the models provided, press and ro-
tate the knob in the piezoelectric po-
sition (Part 1), at the same time press
the button (Part 4) until the pilot flame
light on. Release the knob after 20 "and
visually check that the pilot light is on.
Once the pilot flame ignition procedure
is completed, turn the burner adjust-
ment knob to the desired temperature
(Part 1).
LOADING / UNLOADING THE PRO-
DUCT - see SECT. IMAGES - REF.
v) Load the product to be cooked in
the specific container and place it in
- 19 -
9.
EN