Martin Yale 278-4S Instrucciones De Uso página 7

http://www.monomachines.com/
Translation of the Original Operation Manual
GB
Übersetzung der Originalbetriebsanleitung
MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed in
the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display
on.
Proceed as follows:
Paper jam in paper feed slot (12)
- Remove the paper that has been fed back.
- The cutters now run forwards automatically and
shred the remaining paper in the cutters. During
the forward run the forward button (3) LED
display comes on. The control display
goes out.
- Continue shredding with less paper.
Material jam in CD/DVD feed slot (13)
- Remove the returned material.
Remove the material
because there is the risk of being
injured by the sharp cut surfaces.
- The remaining material to be cut is now
automatically fed to the cutters again and
shredded. During the forward run the forward
button (3) LED display comes on. The control
display (6) goes out.
- If the material to be cut has gone through continue
shredding with the right amount of material.
- If necessary, switch the cutters manually
alternately from forward to reverse until the
material has gone through completely and been
shredded.
CLEANING THE PHOTOCELLS (Fig. 5):
If paper particles should come to rest in the inlet guide (for
example after a paper jam) it is possible that the machine will
not turn off, due to the broken light barrier.
To remove these paper strips and also to clean the photocell,
pass another sheet of paper through the feed slot, or switch
the machine to reverse and wipe both "eyes" of the photocell
with a brush.
fi g. 5
Model Cutting width
paper / CD,DVD
intimus 45SC2 3.8 mm / 8 mm
intimus 45CC3 3.8x30 mm / 8 mm
intimus 45CC4 1.9x15 mm / 8 mm
intimus 60/90SC2 3.8 mm / 8 mm
intimus 60/90CC3 3.8x30 mm / 8 mm
intimus 60/90CC4 1.9x15 mm / 8 mm
Model
intimus 45SC2 220-230V/50Hz, 3.0 amps
intimus 45CC3 220-230V/50Hz, 3.0 amps
intimus 45CC4 220-230V/50Hz, 3.0 amps
intimus 60/90SC2 220-230V/50Hz, 3.0 amps
intimus 60/90CC3 220-230V/50Hz, 3.0 amps
intimus 60/90CC4 220-230V/50Hz, 3.0 amps
http://www.monomachines.com/
All manuals and user guides at all-guides.com
MALFUNCTIONS
SIMULTANEOUS MATERIAL FEED:
Should material be fed into the two feed slots at the
same time the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display
(6) comes on.
- Take the material out of one of the slots.
- Press the forward button (3) briefl y. The material
in the other slot is fed to the cutters and shredded.
The control display
LIGHT BARRIER COVERED
WHEN DOOR OPENED:
(6) Should there still be material in one of the two feed
slots when the door is opened, the motor switches
off and the cutters stop. The control display
comes on.
Close the door and acknowledge the status by
carefully pressing the forward button (3) briefl y. The existing
material is fed to the cutters and shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in one of the two feed
slots when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the status
by pressing the forward button (3) briefly.
MAINTENANCE / DISPOSING
CUTTER MAINTENANCE (CROSS CUT):
Cross cut cutters must be oiled after a specific
operating time.
If the control display
follows:
Open the door. The control display
the reverse button (4) LED display
display (7) flashes. Remove the oil reservoir (17) (Fig. 6)
from the holder in the door and close the door again.
Pour a little oil onto a sheet of paper and then feed this
through the paper feed slot (12) onto the cutters.
The paper is drawn in and in this way the oil is distributed
to the cutters.
Note: This procedure is acknowledged as follows to turn
off the display after the cutters have been oiled:
- Open the door until the control display
17
control displays
- Press the reverse button
fi g. 6
the control display
TECHNICAL DATA
Cutting capacity Working width
paper / CD,DVD
22-24 sheets* / 1 piece 260 mm
16-18 sheets* / 1 piece 260 mm
11-13 sheets* / 1 piece 260 mm
22-24 sheets* / 1 piece 260 mm
16-18 sheets* / 1 piece 260 mm
11-13 sheets* / 1 piece 260 mm
Power supply data
supply voltage / frequency / current consumption
115-125V/60Hz, 5.6 amps
115-125V/60Hz, 5.6 amps
115-125V/60Hz, 5.6 amps
115-125V/60Hz, 5.6 amps
115-125V/60Hz, 5.6 amps
115-125V/60Hz, 5.6 amps
(6) comes
(6) goes out.
(6)
- Close the door again.
The cutters now start a cleaning cycle automatically (forward
and reverse run) and then switch off. The machine is ready
(7) comes on proceed as for use again. Should you need to re-order the special oil see
"SPECIAL ACCESSORIES".
(8) comes on and
AUTOMATIC ENERGY SAVING:
as well as the control
If the machine is not used for a while it automatically switches
off after about 5 minutes. The function button (2) LED display
turn it on again.
DISPOSING OF THE MACHINE:
(8) lights up. The
(7) and (4) flash.
(4) and keep it held down until
(7) goes out.
Power Noise level Intermittent operation
0.7 kW app. 55 dB(A)
0.7 kW app. 55 dB(A)
0.7 kW app. 55 dB(A)
0.7 kW app. 55 dB(A)
0.7 kW app. 55 dB(A)
0.7 kW app. 55 dB(A)
100V/50/60Hz, 7.0 amps
100V/50/60Hz, 7.0 amps
100V/50/60Hz, 7.0 amps
100V/50/60Hz, 7.0 amps
100V/50/60Hz, 7.0 amps
100V/50/60Hz, 7.0 amps
7
MOTOR PROTECTION:
Should the motor be overloaded it switches off. The
control display (9) comes on.
The machine can be started again after a cooling
down period of about 25 – 40 minutes (depending
on the model and the room temperature).
ELECTRICAL FAULT:
If the control display (9) flashes together with
the function button (2) LED display
control display (8) flashes there is an electrical
fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the following
points:
- is the plug connected to the power supply?
- is the door closed?
- is the paper collection bag full?
Follow the instructions for "EMPTYING THE
PAPER COLLECTION BAG".
- Is the CD/DVD collection container full?
Follow the instructions for "EMPTYING THE CD/
DVD COLLECTION CONTAINER".
- Is there a material jam in the machine?
Follow the instructions in "MATERIAL JAM IN
THE MACHINE".
- Is the motor overloaded?
See "MOTOR PROTECTION".
If none of these test points apply, please
contact your dealer.
for "Ready" goes out. Press the function button briefl y to
Dispose of the machine in an environmentally
friendly fashion at the end of its useful service life.
Do not dispose of any of the parts included in the
machine or its packaging with household waste.
Dimensions
ON / OFF W x D x H
45 / 60 min 450 x 390 x 650 mm
45 / 60 min 450 x 390 x 650 mm
45 / 60 min 450 x 390 x 650 mm
45 / 60 min 450 x 390 x 770/990 mm
45 / 60 min 450 x 390 x 770/990 mm
45 / 60 min 450 x 390 x 770/990 mm
* based on A4-paper 70g/m² at 230V/50Hz – 10%
SPECIAL ACCESSORIES
Description
Plastic bag, 440x330x600x0.05 mm (45)
Plastic bag, 440x330x950x0.05 mm (60/90)
Lubricant, 110 ml bottle
Note: For orders of special accessories and spare
parts, please contact your dealer.
or only the
Weight
31 kg
32 kg
32 kg
33/37 kg
34/38 kg
34/38 kg
O rder-No.
83079
99977
88035