Kenwood KCL95 Instrucciones página 17

To Fit And Remove Your Stir Assist Clip
Refer to Illustration W
The stir assist clip can be used to assist the mixing action.
1 Slot the stir assist clip over the side of the bowl with the
vertical ridge on the inside and the clips on the outside.
2 Turn the clip anti-clockwise onto the bowl handles.
3 To remove, reverse the procedure.
IMPORTANT - The stir assist clip should not be fitted when
using the K-beater, whisk, dough tool or creaming beater.
Assembling The High Temperature
Creaming Beater
Refer to Illustration X
Fitting The Wiper Blade
The wiper blade is supplied already fitted and should always
be removed before cleaning.
1 Carefully fit the flexible wiper blade onto the tool by
locating the base of the wiper blade into the slot then fit
one side into the groove before gently hooking the end in
place. Repeat with the other side.
Care And Cleaning
Always switch off and unplug before cleaning.
A little grease may appear at outlet
it. This is normal - just wipe it off.
The metal surfaces of the temperature sensors may show
signs of wear during normal use. This does not affect the
performance of the product.
Do not leave the high temperature flexible beater fitted to
the mixer when not in use.
Appliance, outlet covers
Wipe with a damp cloth, then dry.
Never use abrasives or immerse in water.
High temperature creaming beater
Always remove the flexible wiper blade from the tool
before cleaning.
Wash the flexible wiper blade and tool in hot soapy water,
then dry thoroughly. Alternatively the parts can be washed
in a dishwasher.
Note: Please inspect the condition of the tool body before and
after use and also regularly inspect the condition of the wiper
blade and replace it if there are any signs of wear.
Bowl, Tools, Splashguard, Stir Assist Clip
Wash by hand, then dry thoroughly or wash in the
dishwasher (refer to chart at front of manual).
Never use a wire brush, steel wool or bleach to clean your
stainless steel bowl. Use vinegar or a suitable descaler to
remove limescale.
If food sticks or burns on the inside of the bowl, remove as
much as possible using the spatula provided. Fill the bowl
with warm soapy water and allow to soak. Remove any
stubborn deposits using a nylon brush.
Any discolouration of the bowl will not affect its
performance.
Drain Hole
Ensure this area is free from food. If necessary use a pipe
cleaner or cotton bud to clean.
Temperature sensors
Wipe with a damp cloth then dry thoroughly. Never use
abrasives or sharp instruments to clean the sensors.
Steamer Attachment
when you first use
13
Always switch off and unplug before removing the
attachment from the Stand Mixer.
For easier cleaning always wash the parts immediately
after use.
All parts can be washed in hot soapy water, then dried
thoroughly. Alternatively they can be washed in the
dishwasher.
Ordinary water and food contains salts and acids which
can sometimes effect metal surfaces such as the inside of
the mixer bowl. Should this occur clean with a nylon brush,
a non abrasive scourer or a proprietary stainless steel
cleaner.
Service and Customer Care
If you experience any problems with the operation of
your appliance, before requesting assistance refer to the
'Troubleshooting Guide' section in the manual or visit
www.kenwoodworld.com.
Please note that your product is covered by a warranty,
which complies with all legal provisions concerning any
existing warranty and consumer rights in the country
where the product was purchased.
If your Kenwood product malfunctions or you find
any defects, please send it or bring it to an authorised
KENWOOD Service Centre. To find up to date details of
your nearest authorised KENWOOD Service centre visit
www.kenwoodworld.com or the website specific to your
Country.
Designed and engineered by Kenwood in the UK.
Made in China.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF
THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN
DIRECTIVE ON WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT (WEEE)
At the end of its working life, the product must not be disposed
of as urban waste. It must be taken to a special local authority
differentiated waste collection centre or to a dealer providing
this service.