gefran AGL50-EV Manual De Instrucciones página 60

PARAMETER
Code
Name
A.300 AND1 In 1 src Source of In 1 of logic block AND1
A.301 AND1 In 2 src Source of In 2 of logic block AND1
A.302 AND2 In 1 src Source of In 1 of logic block AND2
A.303 AND2 In 2 src Source of In 2 of logic block AND2
A.304 AND3 In 1 src Source of In 1 of logic block AND3
A.305 AND3 In 2 src Source of In 2 of logic block AND3
A.306 OR1 In 1 src Source of In 1 of logic block OR1
A.307 OR1 In 2 src Source of In 2 of logic block OR1
A.308 OR2 In 1 src Source of In 1 of logic block OR2
A.309 OR2 In 2 src Source of In 2 of logic block OR2
A.310 OR3 In 1 src Source of In 1 of logic block OR3
A.311 OR3 In 2 src Source of In 2 of logic block OR3
A.312 NOT1 In src Source of Input of logic block NOT1
A.313 NOT2 In src Source of Input of logic block NOT2
A.314 NOT3 In src Source of Input of logic block NOT3
A.315 NOT4 In src Source of Input of logic block NOT4
A.320 Timer 1 mode Select working mode of Timer 1
A.321 Timer 1 set src Select input signal of Timer 1
A.322 Timer 1 delay Set delay of Timer 1
C.000 Save parameters Save parameters command
C.001 Recall param Recall last set of saved parameters
C.002 Load default Recall of the factory parameters.
C.020 Alarm clear Reset of the the Alarm List register
C.040 Reserved
C.041 Reserved
C.050 Rst MdplcPrecRun Reset mdplc error at previous run
C.060 Calculate space Off line space evaluation
C.070 Reserved
C.071 Reserved
C.100 Measure stator R Motor Autotune command
60
DESCRIPTION
[1] Mltspeed !=0
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
see list of I.000
[0] Disable
[1] On delay
[2] Off delay
[3] On/Off delay
[4] Pulse
[5] Sym flasher
See list of I.000
See list of I.000
off
do
off
do
off
do
off
do
off
do
off
do
off
do
PICK LIST
Selection Description
You can activate the
start sequence with
multispeed selection.
The Multispeed value di-
fferent from zero causes
the start of sequence.
The Run Fwd command
or Run Rev command
must be present.
COMMAND
No action.
Save parameters
command.
No action.
Recall last set of saved
parameters.
No action.
Load default parameters.
No action.
Clear alarm register
command.
No action.
Reset mdplc error
No action.
Start
No action.
Autotune command.
Def. Min Max Unit
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 27
0 0 5
0 0 27
3.00 0.00 30.00 sec
off off do
off off do
off off do
off off do
off off do
off off do
off off do
Variat. IPA
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1375
1376
0.01 1377
800
801
802
803
809
809
806
AGL50-EV