Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY INSTRUCTIONS
TO AVOID SERIOUS OR FATAL PERSONAL INJURY
OR MAJOR PROPERTY DAMAGE, READ AND
FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL
AND ON PUMP.
THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.
This is a SAFETY ALERT SYMBOL.
When you see this symbol on the pump
or in the manual, look for one of the fol-
lowing signal words and be alert to the
potential for personal injury or property
damage.
Warns of hazards that WILL cause
DANGER
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause
WARNING
serious personal injury, death or major
property damage.
Warns of hazards that CAN cause per-
CAUTION
sonal injury or property damage.
NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.
THOROUGHLY REVIEW ALL INSTRUCTIONS
AND WARNINGS PRIOR TO PERFORMING ANY
WORK ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.
All electrical work must be performed
WARNING
by a qualified technician. Always follow
the National Electrical Code (NEC), or the Canadian
Electrical Code, as well as all local, state and provincial
codes. Code questions should be directed to your local
electrical inspector. Failure to follow electrical codes and
OSHA safety standards may result in personal injury or
equipment damage. Failure to follow manufacturer's
installation instructions may result in electrical shock,
fire hazard, personal injury or death, damaged equip-
ment, provide unsatisfactory performance, and may void
manufacturer's warranty.
Standard units are not designed for use in
WARNING
swimming pools, open bodies of water,
hazardous liquids, or where flammable gases exist. These
fluids and gases may be present in containment areas.
Tank or wetwell must be vented per local codes.
Only pumps specifically Listed for Class 1, Division 1
are allowable in hazardous liquids and where flammable
gases may exist. See specific pump catalog bulletins or
pump nameplate for all agency Listings.
Disconnect and lockout electrical power
WARNING
before installing or servicing any electrical
equipment. Many pumps are equipped with automatic
thermal overload protection which may allow an over-
heated pump to restart unexpectedly.
PRE-INSTALLATION CHECKS
Open all cartons and inspect for shipping damage. Report
any damage to your supplier or shipping carrier immedi-
ately.
Important: Always verify that the pump nameplate Amps,
Voltage, Phase, and HP ratings match your control panel
and power supply.
Many of our sewage pumps are oil-filled. If there are any
signs of oil leakage or if the unit has been stored for an
extended period check the oil level in the motor dome
and the seal housing, if so equipped.
Check the motor cover oil level through the pipe plug on
top of the unit. The motor chamber oil should just cover
the motor. Do not overfill, leave room for expansion!
If low, refill with an ASTM 150 turbine oil. Replace the
plug.
Oil is available in 5 gallon cans through our distributors.
You can also source oil locally at motor repair shops.
Typical oil brands are: Shell Turbo 3, Sunoco Sunvis
93, Texaco Regal R&O 3, Exxon Nuto 3 and Mobil
DTE Light.
Check the strain relief nut on power cable strain assem-
blies. Power cables should be torqued to 75 in. lbs. for
#16 cables and 80 in. lbs. for all other cable assemblies.
Warranty does not cover damage caused by connecting
pumps and controls to an incorrect power source (volt-
age/phase supply).
Record the model numbers and serial numbers from the
pumps and control panel on the front of this instruction
manual for future reference. Give it to the owner or affix
it to the control panel when finished with the installation.
LIFTING OF PUMP
DO NOT LIFT, CARRY OR HANG
WARNING
PUMP BY THE ELECTRICAL
CABLES. DAMAGE TO THE
ELECTRICAL CABLES CAN CAUSE
SHOCK, BURNS OR DEATH.
Hazardous voltage
can shock, burn or
cause death.
Lift the pump with an adequately sized chain or cable at-
tached to the lifting eye bolt. DO NOT damage electrical
and sensor cables while raising and lowering unit.
OPTIONAL GUIDE RAIL
OR LIFT-OUT SYSTEM
In many effluent and sewage basins or lift stations it is
advisable to install the pump on a guide rail system or on
a lift-out adapter to facilitate installation and removal for
inspection and/or service. Most codes do not allow per-
sonnel to enter a wetwell without the correct protective
equipment and training. Guide rails are designed to allow
easy removal of the pump without the need for entry
into the wetwell or need to disturb piping. The guide rail
or lift-out adapter should locate the pump opposite the
influent opening preventing stagnate areas where solids
can settle. The basin or pit must be capable of supporting
the weight of the pump and guide rail. The pit floor must
be flat.
NOTICE: FOLLOW THE INSTRuCTIONS THAT
ARE PROVIDED WITH THE GuIDE RAIL
ASSEMBLY.
3
Publicidad
