Bobike Go Maxi Frame Instrucciones Específicas página 21

3. Desingage and remove the metallic support bar (H)
from the child seat, pulling it backwards. Desingage
and remove the metallic mounting plate (J).
4A. Only for Bobike Go Maxi Frame: Hold the
metallic support bar (H) the same as in the picture
and pass it through the opening in the child bicycle
seat.
4B. Only to Bobike Go Maxi Frame Reclinable
System: Stand the metallic support bar (H) on the
bottom of the reclining system plate (L).
5. In order to adjust the child bicycle seat according
to the bicycle size, set the metallic support bar (H)
into one of the allowed positions to move the seat
backward or forward. At the beginning we suggest
to place it on the position No. 3. The seat shall be
installed as close to the saddle as possible.
6. Insert the metallic mounting plate (J) on the
grooves of the child bicycle seat, and close it as
indicated in the picture.
7. Place the screw (J1) into the metallic mounting
plate (J) fixing both into to the seat (A). Then tighten
it securely with the key (I5). We recommend a torque
of 4 N.m. Tighten tightly so that the metallic support
bar (H) is securely fastened. This extremely important
for cyclist and child safety.
8. Remove the screws (I1+I6) on the frame holder (I),
with the Allen key no. 5 (I5).
9. Before placing the frame holder onto the frame,
make sure that the protective rubber (I8) is correctly
positioned on front of the plastic mounting block (I2).
Place the main body of the plastic mounting block
(I2) on the front of the bicycle frame, and then place
the metallic mounting plate (I4). Note: If they are
cables in this area make sure that they are correctly
positioned in the central groove of the metallic plate,
(between the protective rubber (I8) and the groove of
the mounting plate (I4) and are able to move freely).
Place the washer (I6) in the M8 screws (I1), and then
screw them on to the frame holder (I).
How to safely place and secure the child on the seat
16. To safely place the child on the seat you must place
the bicycle on flat and solid ground for maximum
bicycle stability. Even if your bicycle offers robust
quick stands, you must always hold the bicycle, while
placing/ removing the child. You must carry your
child in your lap and safely place him on the seat. It´s
forbidden for the child to climb alone on the bicycle
or using the footrests to reach the seat. To place the
child in the seat, first fully extend the retention system
harness (B), sliding all the strap adjusters (B2, B3) - this
makes it easier to put the child in the seat. Then, open
the safety buckle (B1) by pressing the safety buckle
button. Seat the child, place the shoulder strap and
then close the safety buckle, adjust the belt length
using the strap adjusters, so that your child is securely
restrained. Before starting the journey, always check
that the child is secured and that the belt is snug but
not so tight that it hurts the child.
17. According to the child growth, current height,
and weight, you can adjust the height of the retention
system harness (B) on all the strap adjusters (B2, B3),
10. Place the edges of the metallic support bar (H) at
the holes of the frame holder (I) until you hear a click
indicating the lock, and until the 2 green safety device
indicators pop up on the front of the mounting block.
The child bicycle seat will only be properly installed
when the 2 green safety device indicators are visible.
This step is extremely important for the child's safety.
11. Center and adjust the metallic support bar (H)
at a height above the rear wheel, so that later, when
you add the weight of the child, the child's bicycle
seat does not touch the wheel. Note that the metallic
support bar (H) should be positioned at a maximum
of 10 cm away from the wheel. Never use this metallic
support bar (H) to carry any other loads than this
child seat, as indicated in this manual.
12. The child seat has a centre of gravity (D) (inscribed
on the child seat) that must be positioned in front of
the rear wheel axle. If it is positioned behind the axle,
the distance must not exceed 10 cm. Special care
must also be taken when positioning the child seat
to ensure that the cyclist does not touch the child
seat with his feet when cycling. Note: In Germany,
according to the German Traffic Law StVZO, bicycle
seats may only be fixed so that 2/3 of the seat depth
or the Gravity Center of the seat is located between
the front and rear axle of the bicycle.
13. After adjusting the height and positioning of the
seat, hand tighten the frame holder (I) to ensure that
it cannot move. You need to hand tight the screws
diagonally, with the same force and in stages. We
recommend a torque of 8 N.m. Make sure that the
frame holder (I) is firmly attached.
14. We suggest shaking the seat to make sure it´s
properly and securely attached to the frame tube.
This extremely important for cyclist and child safety.
15. Start to open the safety belt buckle (C1) and pass
it around the bicycle frame. Adjust the belt it as shown
in the picture, under tension. Make sure that remain
loosen belt is not in contact with the wheel, so pass
it trought the Safety belt retainer (C2). This step is
extremely important for the cyclist and child safety.
by pulling up or down the straps until reaching the
desired size. You can also adjust the height of the
retention system harness (B) by choosing between
the available holes for retention system adjustment
(B4). To adjust it, remove the retention system clip
from the current hole and place it on the best hole
according to your child height.
18. Adjust the height of the footrest according to the
size of the child. To do this, raise the lever (E1) and slide
it up or down for the required height. After deciding on
the correct height, lower the lever (E1) to lock in place.
19. To remove the footrest strap (E3), lift it slightly
to release it from the footrest peg (E2) and slide it
upwards to disengage it from the footrest slot. Then
pass the thin end of the plastic strap through the
hole in the footrest, as shown in the picture. Once the
strap is correctly positioned, it can be easily slid up or
down according to the child's foot. Next slot one of
the openings in the strap over the foot support peg. If
you want to remove the strap (E3), twist it slightly to
loosen it from the foot support peg (E2).
21