Publicidad
Idiomas disponibles
Idiomas disponibles
Installation
Instructions
ELECTRICAL REOUIREMENTS FOR
ELECTRIC DRYERS
This dryer
must
be connected
to an individual
branch circuit, protected
by the required time-delay
fuses or circuit
breakers.
A three-
or four-wire,
single-phase,
120/240V or 120/208V, 60Hz, 30-amp
circuit is required.
If the
electric
supply
does
not meet the above
specifications,
then call a licensed electrician.
ELECTRICAL REQUIREMENTS FOR
ELECTRIC DRYERS (CANADA)
This dryer
must
be connected
to an individual
branch circuit, protected
by the required time-delay
fuses or circuit
breakers.
The power
supply must
be of 120/240
volts,
60Hz circuit
with
the wall
receptacle
as shown below.
TYPICAL 30 AMP
RECEPTACLEFOR DRYER
The power supply must be protected
with 30 Amp
fuses or breakers.
It must be well grounded
and
conform
to local codes.
GROUNDING
INSTRUCTIONS
This dryer
must
be connected
to
a grounded
metal, permanent
wiring system, or an equipment-
grounding
conductor
must be run with the circuit
conductors
and
connected
to
the
equipment
grounding
terminal
on the appliance.
GROUNDING
INSTRUCTIONS
(CANADA)
This appliance
must
be grounded.
In the event
of
malfunction
or
breakdown,
grounding
will
reduce
the risk of electrical
shock
by providing
a path of least resistance
for electrical
current.
This appliance
is equipped
with a cord having an
equipment-grounding
conductor
and a grounding
plug. The plug must be plugged into an appropriate
outlet that
is properly
installed
and grounded
in
accordance
with all local codes and ordinances.
23
CONNECTING
DRYER USING 4-WIRE
CONNECTION
(MUST BE USED FOR
MOBILE HOME INSTALLATION)
NOTE: Since January 1, 1996, the National Electrical
Code requires that new constructions
utilize a
4-wire connection
to an electric dryer. A 4-wire cord
must also be used where local codes do not permit
grounding
through the neutral.
3-wire connection
is NOT for use on new
construction.
Relocatre
Green
green ground
Hot Wire
Screw Wire
screw here
/4#10 AWG
Screw
I
minimum
Remove
ground strap
and
Keepgreen
ground Neutral
screw.
(white)
Hot Wire
Strain
Screw 3//4" UL
Relief
Recognized Bracket
Strain Relief
conductors
or 120/2/40V
30A power
supply cord kit
marked for use
with dryers
and provided
with closed
loop or spade
terminals with
upturned ends
(not supplied)
.
2.
3.
4.
5.
.
.
.
9.
Turn off the circuit breaker(s) (30 amp) or remove
the dryer's circuit fuse at the electrical
box.
Be sure the dryer cord is unplugged
from the wall
receptacle.
Remove
the power
cord cover
located
at the
lower back.
Remove
and discard
ground
strap.
Keep the
green ground screw for Step 7.
Install 3/4 in. UL-recognized
strain relief to power
cord entry hole. Bring power cord through
strain
relief.
Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of
the terminal
block (marked L1 and L2).
B. Connect the neutral (white) line to the center of
the terminal
block (marked N).
Attach ground wire of power cord with the green
ground
screw (hole above strain relief bracket).
Tighten all terminal
block screws (3) securely.
Properly secure power cord to strain relief.
Reinstall the cover.
A, WARNING - NEVER
LEAVETHE
COVER OFF OF THE TERMINAL BLOCK.
Publicidad
