Imesa IM6 Instrucciones De Uso página 29

E030101C
EXAMPLE:
parameters. Max. level 25 cms, min. level
10 cms, temperature 40° C, lapse 5° C.
Washer starts cooling down by draining
warm water down to 10 cms level, loading
then cold water up to 25 cms, keeping
temp. alteration under control within a
range of 5° C cooling per minute.
- TEMPERATURE: is end step (in ° C)
EXAMPLE
temperature parameter of 90° C elements
will heat up to above 90° C
EXAMPLE 2: cooling step for temperature
parameter of 30° C , cooling will keep on
until water temp. will be under 30° C
- TIME is end step in seconds.
EXAMPLE 1: loading step for detergent 1;
parameter is time, 30 seconds: detergent
will be loaded for 30 secs
EXAMPLE
parameter is time 5 mins.: spinning will
last 5 mins.
- WDT: watch-dog time = max. allowed
time to complete step (in minutes)
example: loading
parameter in 15 cms. of water with 30
mins. WDT. 15 cms of water will be
loaded within 30 mins., if not, alarm will
ring.
PLEASE NOTE that during programming, some
parameters may not appear if they are not
compatible to the related step (i.e. in a step of
spinning duration, temperature does not appear).
23.MOTOR TYPES
Motor Type is a step parameter; motor types
available are 16, identified by numbering: 1,2,3,4,
and so on. First 4 are factory-stored in the
microprocessor (see § 30) and may anyway be
modified. Motor types are free from 5 to 15
MOTOR TYPE NO. Main specs composing Motor
Type are: clockwise and
Anti-clockwise rotation (in seconds), interval time.
Motor type "NO" does not have rotations times. If
selected, the motor does not turn for all the step.
PLS NOTE that not all steps have motor as a
parameter. For instance linen distribution and
spinning only turn clockwise.
24. SET-UP/MODIFICATION OF MOTOR TYPES
Modifying a motor type means modifying rotation
and interval times in a step parameter. PLEASE
NOTE that when modifying a motor type, all
programmes containing that motor type will be
affected.
Example: set-up/modification of motor type 5 to
consist of: 20 secs clockwise rotation, 10 secs
interval, 20 secs anti-clockwise rotation.
To enter programming, open door, display shows
"DOOR OPEN", press "MENU", display shows
cooling step and
1: heating step
2: step is spin duration,
step has
its "PASSWORD", press 6 times on "START".
Display
PROGRAMMES". Use "+" & "-" to scroll main
menu, until display shows "SET-UP/MODIFY
MOTOR TYPE" . Press "ENTER", display shows
"MOTOR TYPE 1". Use "+" & "-" to scroll motor
types until display shows "MOTOR TYPE 5" ,
press "ENTER" to select. Use "+" & "-" to scroll
motor types parameters. To modify a parameter
for
value press "ENTER" and use "+" & "-" to increase
or decrease.
parameters as per example: FORWARD (20
secs.) INTERVAL (10 secs), BACKWARDS (20
secs.). When all parameters are programmed,
press "MENU" more times to scroll upwards to
other menus.
25. LANGUAGE SWITCH
Our microprocessori
languages. To select a language, pls open door ",
display shows "DOOR OPEN", press "MENU",
display shows "PASSWORD", press 6 times on
"START", display shows " PROGRAMMES SET-
level
UP/MODIFICATION. Use "+" & "-" to scroll main
menu until display shows "LINGUA". Press
"ENTER" to select. Use "+" & "-" to choose
available languages and "ENTER" to confirm
language choice. Press "MENU" more times to
scroll upwards to other menus.
26. CONNECTION TO PERSONAL COMPUTER
Wizard software may connect your PC to our
micorprocessor. In this case washer must be
equipped with serial gate RS232 (9 pins –
optional) to be connected by means of a cable (as
option) with following specs:
- 3 pole cable with net;
- 9 pins serial gate RS 232 –female plugs
on both cable ends;
- designation as A & B for cable ends.
Wire the cable connecting pin 2 - A to pin
3 - B;
connect pin 3 - A to 2 - B
connect pin 5 - A to 5 - B
- both on gate A and B make a bridge
between the pin 1,4,6 and anothe one
among the pin 7,8
- connect cable-net to 5 - A
Directions for use of Wizard are included in
"HELP" of its software
27. MODEM COMMUNICATION
Some washing machine models are equipped with
modem.
communication,
connection, between the microprocessor IM6 and
a remote PC. On remote PC install the modem
driver following the instruction of "Rapid Guide",
supplied with the machine.
29
shows "SET-UP/MODIFY
In this motor
s set up
This instrument
with non mobile
30/11/2003
type, modify
in several
allows the
telephone