SFA Compact Serie Instrucciones De Instalación página 23

5.5.2 SANIMARIN LUXE
Orange
LED
LED BUZZER
OFF green OFF
OFF orange
OFF green 4 beeps when a
key is pressed.
ON flashing orange
(«FULL» message
visible)
OFF green 4 beeps when a
key is pressed.
ON solid orange
(«FULL» message
visible)
Override of the system when 3rd status is reached
Pressing «NORMAL» for 5 seconds will return cycles to normal
operation.
IMPORTANT
Prolonged use of the toilet when black water tank is full
can lead to overflow.
Ö Disabling the locking system is strongly discouraged.
6. CLEANING/MAINTENANCE
NOTICE
Ö If away for a long period (holiday,...) or in the
event of a long interruption of electricity, the water
and electricity supplies to the Sanimarin® should be
switched off (see procedure in "Wintering").
DANGER
Ö Before you begin any work on this product,
make sure that:
- all electrical power to the unit has been
switched off,
- and that the through-hull valves are in the
CLOSED or STOP position.
6.1 CLEANING
• For cleaning, use normal sanitary products.
• Do not use aggressive chemicals (such as acetone, pure
bleach, etc.) that could damage the material of the bowl.
• Use a suitable standard toilet brush; do not use scouring or
abrasive pads.
6.2 WINTERING
In the event of a long period without use,
• rinse the bowl, carry out several flushing cycles with the fresh
water,
• empty the bowl (see
5. Use
• close through-hull valves.
7. FAULT FINDING
In most cases, any inconsistencies in the operation of the unit
will be minor and easily rectified. Please refer to the chart
below. If the problem cannot be easily remedied thanks to this
chart, please call our Saniflo Service organisation or go to a
Saniflo-approved engineer.
DISCONNECT THE ELECTRICAL POWER SUPPLY,
BEFORE ATTEMPTING ANY WORK ON THE UNIT.
FAULT PROBABLE
OBSERVED CAUSES
The motor does No electricity
not work. supply.
BUZZER
Green
LED
USE
Normal
3 extra cycles
allowed.
No more cycles
allowed.
Control panel then is
locked until the tank
is emptied.
)
TROUBLESHOOTING
• Check the control switch.
• Check the electrical
connections.
• Check the power source.
FAULT PROBABLE
OBSERVED CAUSES
The motor works The inlet pipe filter
but there is no is clogged.
water inlet for
The water inlet
flushing.
pipe is pinched.
The through-hull
valve is closed.
The pump is
unprimed.
The water injection
nozzle /check valve
is clogged.
The switch is
incorrectly wired
up.
The motor works The outlet is
but there is no clogged.
outlet.
The outlet is too
high.
The through-hull
valve is closed.
There is no water in
the bowl.
The switch is
wrongly wired up.
The motor runs A hard foreign
with a rattling
body has fallen into
noise.
the bowl.
8. GUARANTEE
2 years guarantee from date of purchase, subject to correct
installation and correct use: disposal of toilet papers and faecal
matter only. Guarantee is limited to replacement or service
of the defective spare parts, and any indemnity or claim for
damages will not be included.
Freight and packing costs, travel expenses are not included in
the guarantee. It does not cover any normal deterioration of
the material over time, any external deterioration or accident,
incorrect disposal of sanitary products. Any modification
without prior notice will not be under guarantee. Fixing,
modification, or replacement of parts without our agreement
will not be guaranted, and will invalidate it. Our liability is solely
for the product itself.
Guarantee starts from date of purchase we may request a copy
of the invoice to validate the purchase date.
13
EN
TROUBLESHOOTING
Clean the filter.
Check the pipes.
Check the through-hull
valve.
Check the pump and the
flexible blade turbine.
• Check the water injection
nozzle.
• Check the check valve.
Check the connection of
the cables.
Dismantle and clean the
outlet.
• Change the outlet
• Check and position the
pipe routing.
Check the through-hull
valve.
Add water to the bowl.
Check the connection of
the cables.
• Cut the power supply to
the motor.
• Close the through-hull
valves.
• Remove the motor unit.
• Use a hook to remove all
matter that could interfere
with the rotation of the
shredder.
• Use a tool to rotate the
turbine in both directions
until it turns freely.
• Reconnect the power
supply to the motor and
press a key to check the
operation of the appliance.
• Re-open the through-hull
valves.
• If the macerator is still
jammed we advise you
to contact our service
department who will be
able to advise you or
direct you to one of our
service stations nearest to
your area.