Publicidad
Idiomas disponibles
Idiomas disponibles
LED
BUZZER
OFF green
OFF
OFF orange
OFF green
4 beeps when a
key is pressed.
ON flashing orange
(«FULL» message
visible)
OFF green
4 beeps when a
key is pressed.
ON solid orange
(«FULL» message
visible)
Override of the system when 3rd status is reached
Pressing «NORMAL» for 5 seconds will return cycles to normal
operation.
IMPORTANT
Prolonged use of the toilet when black water tank is full
can lead to overflow.
Ö Disabling the locking system is strongly discouraged.
6. CLEANING/MAINTENANCE
NOTICE
Ö If away for a long period (holiday,...) or in the
event of a long interruption of electricity, the water
and electricity supplies to the Sanimarin® should be
switched off (see procedure in "Wintering").
DANGER
Ö Before you begin any work on this product,
make sure that:
◇ all electrical power to the unit has been
switched off,
◇ and that the through-hull valves are in the
CLOSED or STOP position.
6.1 CLEANING
• For cleaning, use normal sanitary products.
• Do not use aggressive chemicals (such as acetone, pure
bleach, etc.) that could damage the material of the bowl.
• Use a suitable standard toilet brush; do not use scouring or
abrasive pads.
6.2 WINTERING
In the event of a long period without use,
• rinse the bowl, carry out several flushing cycles with the fresh
water,
• empty the bowl (see
5. Use
• close through-hull valves.
7. FAULT FINDING
In most cases, any inconsistencies in the operation of the unit
will be minor and easily rectified. Please refer to the chart
below. If the problem cannot be easily remedied thanks to this
chart, please call our technical support line.
DISCONNECT THE ELECTRICAL POWER SUPPLY,
BEFORE ATTEMPTING ANY WORK ON THE UNIT.
USE
Normal
3 extra cycles
allowed.
No more cycles
allowed.
Control panel then is
locked until the tank
is emptied.
)
FAULT
PROBABLE CAUSES
OBSERVED
The motor does
No electricity supply.
not work.
The motor
The inlet pipe filter is
works but there
clogged.
is no water inlet
The water inlet pipe is
for flushing.
pinched.
The through-hull
valve is closed.
The pump is
unprimed.
The water injection
nozzle /check valve is
clogged.
The switch is
incorrectly wired up.
The motor
The outlet is clogged. Dismantle and clean the
works but there
is no outlet.
The outlet is too high. • Change the outlet
The through-hull
valve is closed.
There is no water in
the bowl.
The switch is wrongly
wired up.
The motor runs
A hard foreign body
with a rattling
has fallen into the
noise.
bowl.
8. WARRANTY
2 Year Warranty from Date of Purchase
A. GENERAL
Subject to the terms and conditions set out in this document,
Saniflo INC., hereafter designated as the Company, guarantees
the consumer to repair or exchange any product or any of its
components (at the discretion of SFA Saniflo Inc) which proves
to be defective. NOTE:
•
year: will
First (1
)
only
st
date of purchase.
•
year: will
Second (2nd)
"replacement parts" at no charge for the remainder of product's
warranty period.
B. TERMS AND CONDITIONS
1. The product must be installed and used as per instructions
supplied and indicated in the product manuals. This is not
limited to but includes the product:
• not be subjected to any negligence, accident or exposure to
"harmful" products or substances.
• installed in strict accordance with local state or provincial
electrical and plumbing codes.
17
TROUBLESHOOTING
• Check the control switch.
• Check the electrical
connections.
• Check the power source.
Clean the filter.
Check the pipes.
Check the through-hull
valve.
Check the pump and the
flexible blade turbine.
• Check the water injection
nozzle.
• Check the check valve.
Check the connection of
the cables.
outlet.
• Check and position the
pipe routing.
Check the through-hull
valve.
Add water to the bowl.
Check the connection of
the cables.
• Cut the power supply to
the motor.
• Close the through-hull
valves.
• Remove the motor unit.
• Use a hook to remove all
matter that could interfere
with the rotation of the
shredder.
• Use a tool to rotate the
turbine in both directions
until it turns freely.
• Reconnect the power
supply to the motor and
press a key to check the
operation of the appliance.
• Re-open the through-hull
valves.
• If the macerator is still
jammed we advise you
to contact our service
department who will be
able to advise you or
direct you to one of our
service stations nearest to
your area.
cover "exchanges" starting from the
cover "repairs" or will provide
only
US
SFA-
Publicidad
