Publicidad
Idiomas disponibles
Idiomas disponibles
Note: Push the button to open lid, then the button naturally stays a ready-to-close place. If
the button goes back, you should push it forward. Otherwise the lid won't be normally closed.
(Fig.10.).
VI. TROUBLE SHOOTING
If any abnormal phenomenon found, turn off the fire immediately and take the cooker to a level place
and shower the cooker with water slowly to reduce the temperature and the pressure. Find the reason
and solve the problem with the table below.
Problem
Steam comes out from the
underside of the lid
Lid can't fix properly
Steam and liquid leaks from the
safety valve suddenly.
Steam and liquid leaks from the
steam-releasing valve.
VII. MAINTENANCE
Please clean the pressure cooker, add to water and heat half an hour before first time using, by
means of cleaning bad smelling.
26
Reason
Solution
1. Clean the sealing ring,
1. Sealing ring is dirty.
cooker mouth and lid.
2.Sealing ring is too old
2.Change the sealing ring
The shape of the lid changed.
Change the lid
1. Take the cooker away
1. The steam-releasing pipe
from the fire and dredge
was obstructed. The safety
the release hole. After
function of the locking pin is
it is cool, take down the
working. The release hole
pressure-limiting valve
of pressure-limiting valve is
and clean the hole of
blocked.
pressure-limiting valve.
2. The safety valve has lost its
2. Change safely open-
function.
preventing valve.
1. Take the cooker away
1. The releasing hole
from the fire. After it is cool,
of pressure regulator is
take down the pressure
obstructed.
regulator and clean the
releasing hole.
2. The safety valve has lost its
2. Change safely open-
function.
preventing valve.
※ Maintenance of the whole cooker.
·Clear away the dirt.
·Then wipe off the water and keep the cooker dry.
·Don't scrape the cooker surface with hard material such as metal to avoid abrasion.
·Don't touch the cooker with other kinds of metal to avoid electro chemical corrosion.
·Don't store food inside the cooker for a long time.
※ Maintenance of the sealing ring (Fig. 11):
·Remove the sealing ring from the
lid. Clear away the dirt from the ring
and the lid with hot water or washing
chemical preparation.
·Wipe off the water and keep the
sealing ring dry.
·Put the sealing ring back to the lid.
Not using the cooker to avoid the
sealing ring being squeezed (Separate from the cooker lid and the cooker body).
※ Maintenance of the safely open-preventing valve, the pressure-limiting valve
Check the pressure limiting valve and the safety open-preventing valve. If it is blocked;
Clear away with the dredging needle, then wash and rinse the pipe with water.
Special dismantling as follows:
The pressure-limiting valve and the steam-releasing hole: switch
the pressure-limiting valve clockwise to the position of
12), press down and turn clockwise to the position of
out the pressure-limiting valve, then clean them(Fig.13); reverse
the lid and clean the sealing washer. After finishing these, install
them as original order.
Pressure-limiting valve should turn to the corner to avoid fly off and hurt people.
※ Pressure-limiting valve just can be switched to
Safety open-preventing valve: switch anti-clockwise safety valve with spanner, then dismantle it. Then
clean it. In order not to influence the pressure and lose the safety valve's function, please do not take
apart the safety valve' s accessories for cleaning.
※ Caution: don't lose small parts such as pressure-limiting valve. There is no problem if the color of the
sealing ring changed. It is suggested to change the sealing ring once in one or two years according the
usage frequency. But it must be changed immediately if there is any damage or shape changing.
Please contact your reseller or the sales department of our company for the replacement parts. Never
use substitutes.
The way of deposit: put it in shade and cool place, the cooker lid place upside downs the cooker body.
※Caution
1. Don't lose small parts such as pressure-limiting valve. There is no problem if the color of
the sealing ring changed. It is suggested to change the sealing ring once in one or two years
according the usage frequency. But it must be changed immediately if there is any damage or
shape changing. Please contact your dealer or the sales department of our company for the
replacement parts. Never use substitutes.
2. The way of deposit: put the body and lid separately in shade and cool place
3. The maintaince of pressure cooker must be made by specialized person.
(Fig. 11)
(fig
, taking
(Fig. 12)
(Fig. 13)
when need cleaning.
27
Publicidad
