Manufacturer's Warranty - REMS Unimat Serie Instrucciones De Uso

eng
To set the chaser die in the holder (Fig. 10) to the dimension 55.4 mm in
the REMS Unimat 75 or to 95.4 mm in the REMS Unimat 77, the screw
of the chucking plate (25) is tightened securely. The stated dimension must
now be set using a dial gauge or the supplied setting gauge (Fig. 8) – as
shown in Fig. 10 – between the lower edge of the holder and the first tooth
after the initial cut. To do this, the die stock chaser must be pressed for-
ward by means of the adjusting screw on the underside of the holder. The
adjusting screw must be in contact with the die stock chaser under pres-
sure. In the case of the REMS Unimat 75, the distance of 55.4 mm (Fig.
10), with a tolerance of +/– 0.05 mm, must be observed. For smaller threads
(diameter 6–12 mm), it can be adjusted to 54.3 mm to good effect. It is,
however, important to maintain the tolerance of 0.05 mm within the 4 die
stock chasers of the die set. In the case of the REMS Unimat 77, it is ad-
visable to observe the specified distance, i. e. 95.4 mm +/– 0.05 mm.
6. Action in the event of faults
6.1. Fault:
Thread ragged, crests and split off.
Cause:
Blunt chaser dies.
•
Bad coolant.
•
Setting dimension of chaser in holder incorrect.
•
Wrong speed.
•
6.2. Fault:
Thread is badly cut, "ragged fine thread".
Cause:
Holder incorrectly inserted in die head. Comply with correct
•
sequence!
Chaser dies incorrectly fitted in holder. Comply with correct sequence!
•
Chaser dies in wrong holder model (inclination angle!).
•
6.3. Fault:
Thread not centered on the workpiece.
Cause:
Vice centering altered.
•
6.4. Fault:
Die head does not open far enough.
Cause:
Wrong closing lever fitted.
•
Closing lever worn.
•
Triggering cam worn.
•
6.5. Fault:
Die head does not close.
Cause:
Clogging.
•
Incorrect insertion of die set (see 3.3).
•
Incorrect fitting of chaser dies in holder (see 5.4).
•

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product
to the first user but shall be a maximum of 24 months after delivery to the
Dealer. The date of delivery shall be documented by the submission of
the original purchase documents, which must include the date of purchase
and the designation of the product. All functional defects occurring within
the warranty period, which clearly the consequence of defects in produc-
tion or materials, will be remedied free of charge. The remedy of defects
shall not extend or renew the guarantee period for the product. Damage
attributable to natural wear and tear, incorrect treatment or misuse, failure
to observe the operational instructions, unsuitable operating materials,
excessive demand, use for unauthorized purposes, interventions by the
Customer or a third party or other reasons, for which REMS is not res-
ponsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service
stations authorized for this purpose by REMS. Complaints will only be
accepted if the product is returned to a customer service station autho-
rized by REMS without prior interference in an unassembled condition.
Replaced products and parts shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the
product.
The legal rights of users, in particular the right to claim damages from the
Dealer, shall not be affected. This manufacturer's warranty shall apply only
to new products purchased in the European Union, in Norway or Swit-
zerland.
eng