Technical Data; Specifications Of The Machine) - EMAK MISTRAL 72/13 H Manual De Uso

WARNING
- Before carrying out unloading operations, always
ensure that there are no people, animals or objects in
GB
the vicinity of the trailer.
- During work always bear in mind that the wheel track of
the trailer is wider than that of the machine by 12 cm, 6
on each side. Dimensions: 112x85x28 cm.
Spreader
After having loaded the hopper with the material to be spread
on the ground, use the graduated lever to adjust the width of
the outfeed to suit your requirements. The accessory is
equipped with a sieve, to retain larger clumps of material that
you do not want deposited on the ground, and a plastic cover,
which can be used for example when spreading rock salt
during rainy or snowy weather, or to cover powdered materials.
Maintenance
- Before or after a long period of storage, use automotive oil

10. TECHNICAL DATA

Electrical system
Battery
Front tyres
Rear tyres
Front tyre pressure
Rear tyre pressure
Overall dry weight
Inside turning circle
Cutting height
Cutting width
Grass-catcher capacity
Ground speed (at 3000 min
- in forward drive
- in reverse drive
Sound pressure level (LpA EN 836/A2)
Uncertainty
Measured sound power level
(LwA 2000/14/EC - EN ISO 3744 - ISO 11094)
Uncertainty
Guaranteed sound power level
(LwA 2000/14/EC - EN ISO 3744 - ISO 11094)
Vibration level (EN 836/A2) steering wheel 3,0(sx)-3,4(dx) m/s
Uncertainty (EN 12096)
Vibration level (EN 836/A2) seat
Uncertainty (EN 12096)
Overall dimensions
34
17 Ah
11" x 4"-4
15" x 6"-6
1,5 bar
1,0 bar
192 kg
3÷8 cm
72 cm
180 litres
-1
):
0÷8,6 km/h
0÷3,2 km/h
90,5 dB (A)
2,0 dB (A)
98,8 dB (A)
1,2 dB (A)
100,0 dB (A)
1,1 m/s
0,47 m/s
0,23 m/s
198x73x110 cm
to lubricate the retaining hook on the tipper body, the locking
pin on the retaining hook and the part of the frame with the
two holes for fixing the machine's towing hitch and
corresponding pin.
- Periodically grease or oil the wheel bearings. Use grease for
wheel bearings or automotive oil.
- Periodically check the tightness of all screws, nuts and
bolts.
- Always keep the tyres sufficiently inflated. Never exceed the
maximum recommended pressure. Incorrectly inflated tyres
(for example inflated to different pressures) may cause loss
of balance.
3) Stone-guard kit
For use in place of the grass-catcher, when the cuttings are
not to be collected.
After having removed the grass-catcher, fit the stone-guard
using the two pins (D, Fig.13) and cotter pins (E).
12 V Key to functional wiring diagram (Fig.25)
Q0 = ignition key switch:
- pos.0 = machine off (pos. OFF)
- pos.1 = machine in reverse with mowing (pos. R)
- pos.2 = machine forward with mowing (pos. 1)
- pos.3 = on (pos. ON)
Q1 = PTO clutch control switch
Q1.1 = 1.2 W blade engaged indicator lamp
H1 = Error warning light
S1 = Machine stopped and travelling microswitch (NC)
S2 = grass-catcher opening micro-switch (NC)
0,9 m
S3 = seat micro-switch (NO)
S4 = parking brake micro-switch (NO)
S6 = grass-catcher full micro-switch (NC)
S7 = machine stopped and reverse gear micro-switch (NC)
S.E. = electronic circuit board
EF = PTO clutch
X.101.S = Engine connector
F1 = Electrical system main fuse (5A)
F2 = Engine main fuse (15A)
F3 = Alternator main fuse (100 A)
X114 = circuit board power supply connector
K108 = starting relay
K115.1 = Engine stop relay
K115.2 = Start enable relay
X118 = PTO clutch connector
M120 = starter motor
MCI = internal combustion engine
G110 = Battery
A = Engine stop
2
B = Alternator
2
Cable colour coding
2
A = light blue G = yellow
2
B = white H = grey
C = orange L = blue
M = brown S = pink
N = black V = green
R = red