Footswitch - Evh 5150 III Guia De Inicio Rapido

time, the three amp channel LEDs will not all illuminate briefly as
the amp channel assignment has not been changed).
If the Program Change message is currently assigned to amp
channel 1 (default), you will have to press channel SELECT {E}
twice to select amp channel 2. If the Program Change message is
currently assigned to amp channel 2, you will have to press chan-
nel SELECT {E} twice to select amp channel 1.
4.
Repeat steps 2–3 for each channel on the amp, if desired. You can
also assign multiple Program Change messages to the same amp
channel for more flexibility.
You can use the Footswitch to temporarily change channels at
any time during MIDI set up and it will have no effect on saving
the amp channel assignments. All channel assignment changes
must be made using the front panel channel SELECT buttons {E
and I}.
5.
Once you are done setting up MIDI Program Changes, press both
channel SELECT buttons {E and I} simultaneously to exit "Learning
Mode." The amp is now set up to switch to the target channels
whenever the selected Program Change messages are sent on
the selected MIDI channel.
The default MIDI channel for the amp is channel 1. You can chan-
ge the MIDI channel for the amp by sending a Program Change
message from any other desired MIDI channel during Learning
Mode. The amp will then only respond to Program Change messa-
ges and Control Change messages on that new MIDI channel.
To use MIDI to switch Reverb on-off:
1.
No set up is required. From MIDI channel 1 (default) or the chan-
nel that was used to send Program Change messages in the
section above (if different from MIDI channel 1), simply send a
Control Change #85 message with a value of 63 or less to switch
reverb off, or a value of 64 or more to switch reverb on.
To clear MIDI programmed setups:
1.
To clear MIDI programming and return the amp to factory defau-
lts, hold down one of the CHANNEL SELECT buttons {E or I} while
powering up the amp.
Type:
PR 2510
Power Requirement:
400W
Speakers: Two 8Ω Celestion® 25W speakers connected in series (total impedance load = 16 Ω)
Input Impedance: >1MΩ
Fuses:
100V units, F4A L, 250V;
Footswitch (included):
4-button, ONE / TWO / THREE / REVERB on-off (P/N 0096467000)
Tube Complement:
Two 6L6GC output tubes, Seven 12AX7 preamp tubes
Height: 25" (63.5 cm) Height (w/castors): 28" (71.1 cm)
Weight: 84 lb (38.1 kg)
T.
U.
V.
W. RESONANCE — Adjusts the low frequency response of the
X.
Y.
Specifications
Power Output: 1 to 50 Watts RMS into 4, 8, or 16 Ohms
Output Impedance: 4Ω / 8Ω / 16Ω (selectable)
120V units, F4A L, 250V;
Width: 27.6" (70.1 cm)
Product specifications subject to change without notice.
FOOTSWITCH — Connect the cable of the supplied footswi-
tch here. The footswitch allows easy selection of any of the
three channels as well as reverb. When illuminated, the Green,
Blue, and Red channel LEDs correspond with the channel LEDs
on the amplifier's front panel.
ONE TWO
EFFECTS LOOP — Connect SEND to effects input and RETURN
to effects output.
PREAMP OUT — Connect to another amp's EFFECTS RETURN
or POWER AMP IN for simultaneous multiple amp use. This
output can also be used to send the preamp signal directly to a
mixer.
power amplifier.
LOAD IMPEDANCE — The EVH 5150-III 2 x 12 Combo includes a
16Ω speaker system and the LOAD IMPEDANCE switch should
be set to 16Ω to match. If an external speaker system is used
in parallel or if the internal speaker system is disconnected, the
IMPEDANCE SWITCH should be set to match the overall spe-
aker impedance load connected to both SPEAKER OUTPUTS.
As an example, if an external speaker system, such as the 16Ω
EVH 5150-III 2 12ST, is connected in parallel with the internal
system, set the LOAD IMPEDANCE to 8Ω.
SPEAKER OUTPUTS — For connection to the internal spea-
kers (16Ω load) and/or external cabinet(s). When using one spe-
aker cabinet, either jack can be used. Use only a high-quality
unshielded speaker cable (P/N 0073411000).
NOTE: A speaker must always be plugged into one of the speaker
jacks when the amplifier is ON or damage may occur. Switch the
amplifier "OFF" or to "STANDBY" while changing speaker con-
nections or impedance settings.
Speaker Configurations are as follows:
SPEAKER SPEAKER
JACK JACK
16Ω + NONE
16Ω + 16Ω
8Ω + NONE
8Ω +
4Ω + NONE
220-240V units, F2A L, 250V;
Depth: 12.1" (30.7 cm)
THREE REVERB
IMPEDANCE
SETTING
= 16Ω
= 8Ω
= 8Ω
8Ω = 4Ω
= 4Ω
9