Anspach eMax 2 Manual De Instrucciones página 13

Table 1: Emission
The Anspach High Speed Electric System is composed of the eMax 2 and eMax 2 Plus Handpiece models: EMAX2 and
EMAX2PLUS; Electric Consoles models SC2100, SC2101, & SC2102; Foot Control models E-FP, E-FP-DIR, E-FP-DIR/
IRR, EPLUS-FP, EPLUS-FP-NS; Hand Controls EMAX2-HC and E-HC.
The Anspach High Speed Electric System is intended for use in the electromagnetic environment specified below. The
customer or the user of the Anspach High Speed Electric System should assure that it is used in such an environment.
Emission test
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations / flicker emissions
IEC 61000-3-3
Table 2: Immunity (all devices)
Guidance and manufacturer's declaration – electromagnetic immunity
The Anspach High Speed Electric System is intended for use in the electromagnetic environment specified below. The
customer or the user of Anspach High Speed Electric System should assure that it is used in such an environment.
Immunity test standard IEC 60601 test level
Electrostatic discharge
(ESD)
IEC 61000-4-2
Electrical fast transient /
burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Voltage dips, short
interruptions and voltage
variations on power
supply lines
IEC 61000-4-11
Note: U is the a.c. mains voltage prior to application of the test level.
T
Power frequency (50/60
Hz) magnetic field
IEC 61000-4-8
Guidance and manufacturer's declaration –
electromagnetic emissions
Compliance
Group 1
Class A
Class A
Complies
Compliance level
±6 kV contact ±6 kV contact
±8 kV air ±8 kV air
±2 kV for power supply ±2 kV for power supply
lines lines
±1 kV for input/output ±1 kV for input/output
lines lines
±1 kV line to line ±1 kV line to line
±2 kV line to earth ±2 kV line to earth
<5% U <5% U
T
(>95% dip in U ) for (>95% dip in U
T
0.5 cycle 0.5 cycle
40% U 40% U
T
(60% dip in U ) for 5 (60% dip in U
T
cycles cycles
70% U 70% U
T
(30% dip in U ) for 25 (30% dip in U
T
cycles cycles
<5% U <5% U
T
(>95% dip in U ) for (>95% dip in U
T
5 sec 5 sec
3 A/m 3 A/m
Electromagnetic environment – guidance
The Anspach High Speed Electric System uses RF energy only
for its internal function. Therefore, its RF emissions are very low
and are not likely to cause any interference in nearby electronic
equipment. RF emissions.
The Anspach High Speed Electric System is suitable for use
in all establishments, other than domestic establishments and
those directly connected to the public low-voltage power supply
network that supplies buildings used for domestic purposes.
Electromagnetic environment -
guidance
Floors should be wood, concrete or
ceramic tile. If floors are covered with
synthetic material, the relative humidity
should be at least 30%
Mains power quality should be that
of a typical commercial or hospital
environment.
Mains power quality should be that
of a typical commercial or hospital
environment.
Mains power quality should be that
T
) for of a typical commercial or hospital
T
environment.
T
) for 5
T
T
) for 25
T
T
) for
T
Power frequency magnetic fields should
be at levels characteristic of a typical
location in a typical commercial or
hospital environment.
11