PLYMOVENT ControlGo Manual De Instalación Y De Uso página 11

Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
Fig. 4.14 Numbering of the filter modules
Digital input 6-12
4.4.5 Compressed air switch MDB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
The compressed air switch monitors the availability of
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
compressed air .
21
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
Valves Indicator LED's
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Power
Light tower
Digital input 6-12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Fig. 4.15 Connection of compressed air switch
Digital input 6-12
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
4.4.6 Compressed air switch + compresse air valve
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SCS / EDS
In case of one (1) SCS / EDS
Besides the compressed air switch, cable #12 connects the
compressed air valve of the SCS / EDS as well.
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Valves Indicator LED's
Power
Light tower
20. Proceed with paragraph 4.4.6 in case of an SCS
21. The system gives a warning signal when there is no compressed air available
0000112607/170717/0 ControlGo
1 2 3 4 5 6 7 8 9 10 11 12
20
Digital input 1-5
Filter Pressure
Digital input 6-12
sensor
cable #8
input IN 10
Digital input 1-5
Filter Pressure
Digital input 6-12
sensor
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 1-5
Valves
1 2 3 4 5 6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Fig. 4.16 Connection of compressed air switch + compressed air valve
Valves
In case of two (2) SCS
1 2 3 4 5 6
Valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
-
+
1 2 3 4 5 6
In case of two SCS systems, you must connect the second one
as a "slave" to the first one ("master").
Fig. 4.16
1 2 3 4 5 6 7 8 9 10 11 12
• Connect the second SCS to output OUT 2.
4.4.7 Input signals (options)
Valves
If desired, you can connect the ControlGo to a start/stop signal
1 2 3 4 5 6
CAN Slave
and/or an alarm signal from an external device
- start/stop signal: cable #4
- alarm signal: cable #5 [remove the wire bridge from input
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
IN 11]
[page 7]
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Valves
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Power
1 2 3 4 5 6 7 8 9 10 11 12
-
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
+
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CAN Slave
Fig. 4.17 Connection of external input signals
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
22. E.g. a welding robot or a timer
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 1-5
Digital input 6-12
Digital input 6-12
Digital input 6-12
Indicator LED's Digital input 1-5
Filter Pressure
Light tower
sensor
Digital input 1-5
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 6-12
Digital input 6-12
cable #12
[page 7]
input IN 10
input OUT 1
Digital inp
1 2 3 4 5 6 7
;
22
-
+
CAN Slave
Digital input 6-12
cable #4
Digital inpu
1 2 3 4 5 6 7
[page 7]
input IN 5
cable #5
[page 7]
input IN 11
EN - 10
1
1
1
1
1