Fan Control - PLYMOVENT ControlGo Manual De Instalación Y De Uso

A
B
C
Fig. 4.7 Connection of the mains cord
4.4.2

Fan control

There are various types of fan control equipment:
- Plymovent VFD/Panel (frequency inverter)
- other type of frequency inverter (third party)
- star-delta switch
- other type of motor starter, e.g. Direct online (DOL)
For more information about the Plymovent VFD/
Panel, refer to the Danfoss documentation that is
supplied with the product.
Connections/functionalities:
- relay output (potential-free contact) for start/stop signal
- alarm input; high input triggers the "Fan alarm"
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
Digital input 6-12
USB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
( rmware updates)
Valves Indicator LED's
Ethernet
Power Light tower
(for service only)
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
NO 1 1
NC 1 2
COM 1 3
4
NO 2 5
NC 2 6
Digital input 6-12
COM 2 7
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
8 8
Fig. 4.8 Connection of fan control equipment
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
16. Max. 30V, 2,5A
0000112607/170717/0 ControlGo
Digital input 6-12
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Digital input 1-5
Filter Pressure
Digital input 6-12
sensor
cable #11
input IN 9
Valves
Power
4.4.3
The SlaveBoard is integrated on the rear of each filter module
MDB-BM/2 and MDB-BM/4 (refer to Fig. II on page 75).
Cable #1 is supplied with a cable gland for connection to the
SlaveBoard box.
Fig. 4.9
• Remove the lid (A).
• Remove the left dust cap (E).
• Loosen the cable gland (C) from the cable and remove the
nut.
• Put the cable into the SlaveBoard and put the nut (B) back
over the cable.
• Connect the cable to the CAN IN connector (D) on the PC
board.
• Tighten the cable gland.
16
Digital input 1-5
1 2 3 4 5 6 7 8 9 10 11 12
-
+
Fig. 4.9 Connection of SlaveBoard
Fig. 4.10
CAN Slave
• Cut the cable to the necessary length for connection to the
Panel.
Valves
1 2 3 4 5 6
[page 7]
Valves
1 2 3 4 5 6
Power
Dustbin
Indicator LED's
sensor
Analog
Light tower
output
Panel  SlaveBoard (MDB only)
- Connect the cable to the SlaveBoard first. Then
cut the cable to the necessary length.
- Start to connect the filter module that is closest to
the Panel.
B
C
A
Valves Indicator LED's
Filter Pressure
Light tower
sensor
Fan Pressure
sensor
Filter Pressure
sensor
cable #1
D
(CAN IN)
E
-
+
Digital input 1-5 CAN Slave
Digital input 6-12
Digital input 1-5
EN - 8
Digital input 6-12