Spare Parts; Electrical Diagram; Disposal - PLYMOVENT ControlGo Manual De Instalación Y De Uso

Symptom problem
Unknown
ALARM: red LED blinking
FILTERS VERSTOPT
FILTER CLEANING
FILTER GESÄTTIGT
FILTRES OBSTRUÉS
5 s
GEEN PERSLUCHT
WARNING ALARM
KEINE DRUCKLUFT
You must still solve the cause of the alarm. If you do not, the alarm
LED remains blinking and you will be unable to restart the system.
Fan/motor
failure
+ buzzer
FILTER CLEANING
External
device
+ buzzer
EXTERN APPARAAT
Unknown
EXTERNES GERÄT
+ buzzer
8.2 Remaining troubleshooting
Symptom problem
panel
White LED No filter
(POWER ON) cleaning
WARNING ALARM
5 .
keeps possible
SEC
blinking
FILTER CLEANING
Filter system
Filter cleaning No optimum
sequence is cleaning
incorrect or performance
illogical
Button FILTER No filter
CLEANING cleaning
cannot be
activated
0000112607/170717/0 ControlGo
possible Solution
cause
NO COMPRESSED AIR
Unknown Restart the system
Contact your
Plymovent
distributor
GEEN PERSLUCHT
COMMUNICATION ERROR
KEINE DRUCKLUFT
Two functions:
ABSENCE D'AIR COMPRIMÉ
- to suppress the buzzer
FALTA DE AIRE COMPRIMIDO
- to reset the alarm LED
COMMUNICATIEFOUT
EXTERNAL DEVICE
KOMMUNIKATIONSFEHLER
ERREUR DE COMMUNICATION
Fan control Repair or replace
ERROR DE COMUNICACIÓN
equipment the fan/motor
defective (connection)
Repair or replace
EXTERN APPARAAT
the fan control
EXTERNES GERÄT
equipment
DISPOSITIF EXTERNE
No Repair the
communication connection
DISPOSITIVO EXTERNO
with external
device
Unknown Restart the system
!
Contact your
Plymovent
distributor
possible Solution
cause
No detection of - Repair the
SlaveBoards connection to the
(MDB only) SlaveBoard(s)
- Make sure that
the setting of the
DIP switches is
correct; refer to
Fig. 4.12 and Fig.
4.13
- If there is no
communication
error (yellow
LED; ref. par.
6.3.1): repeat
the Learning
Mode procedure
(ref. par. 5.3)
Software failure - Try to restart the
during system system
start up - Otherwise:
contact your
Plymovent
distributor
Addressing Correct the setting
sequence is not of the DIP
correct switches; refer to
Fig. 4.12 and Fig.
4.13
No filter Do not activate
cleaning FILTER CLEANING
possible during
the first 40
running hours
(after filter
replacement)
Symptom problem
COMMUNICATION ERROR
Extraction fan
Fan does not No problem
stop
(immediately)
by an
external
COMMUNICATIEFOUT
SERVICE MODE
signal
KOMMUNIKATIONSFEHLER
ERREUR DE COMMUNICATION
9

SpaRE paRtS

ERROR DE COMUNICACIÓN
The following spare parts are available for the product.
SERVICEMODUS
9.1 controlGo/panel
SERVICE-MODUS
Refer to exploded view Fig. VI on page 76.
MODE DE SERVICE
MODO SERVICIO
article no. Description
0000103139 Switch mode power supply 24V DC 2.5A
0000113558 Indicator light yellow 24V
0000113631 PCB main board ControlGo/MDB
0000113632 PCB main board ControlGo/SCS-EDS
0040900180 Main switch 25A
0324000300 Indicator light white 24V
0324000310 Indicator light green 24V
0324000320 Indicator light red 24V
0328050300 Push button green
0328050320 Push button black
0360000060 Buzzer
9.2 control/SlaveBoard
Refer to exploded view Fig. VII on page 76.
article no. Description
0000113561 PCB slave board
10

ELEctRicaL DiaGRaM

Refer to the separately supplied electrical diagram.
11

DiSpoSaL

After life of the product, dispose it of in accordance with
federal, state or local regulations.
possible Solution
cause
Stop delay of 3 Just wait
minutes is
active
SERVI
SERV
SERVI
MODE
MOD
EN - 15