Instructions For The User; Information On The Washing Machine; Use And Ordinary Maintenance - grandimpianti WR-EC 8 Instrucciones Para La Instalación Y Para El Uso

Model Boiler capacity
Mod. 8 45 litres
Mod.11 58 litres
Mod.18 100 litres
Mod.26 146 litres
Mod.33 190 litres
When the connection is finished make sure
that the pipes are not crushed or blocked.
5.7 STEAM CONNECTION
(steam-heated machines only)
The washing machine is fitted with a 3/4"
steam inlet. The incoming steam pressure
must be between 1 and 6 bar (0.1 and 0.6
MPa). The recommended pressure for best
machine performance is between 4 and 6
bar. If doubts should arise, read the rating
plate data. Steam is intended as saturated
and dry.
The water in the tub can be heated either
directly or indirectly. In the latter instance, a
coupling for the recovery of condensed water
will have to be provided for (diameter 3/4").
If the machine is subjected to ISPESL
inspection, keep all ISPESL documents in
the room where the washing machine is
lodged.
When the connection is finished be sure that
the pipe is not crushed or blocked.
5.8 DRAIN CONNECTION
Make certain that the distance between the
machine drain outlet and the floor drain is
not longer than the drain elbow supplied.
Water is drained through a motor-driven
valve that is open (by gravity) when the
machine is not supplied with electricity.
Therefore, the floor drain must always be
lower than the machine drain outlet. The
diameter of the floor drain must never be
smaller than that of the supplied hose.
Model Drain flow-rate
Mod. 8/11/18 80 l/min.
Mod. 26/33 160 l/min.
The drain pipe must be able to resist a
temperature of 90°C.
Install a trap between the hose supplied and
the drain.
Check that the hose is not crushed or blocked.
5.9 AIR BREAK
The washing machine is equipped with an air-
break device to stop wastewater from flowing
back into the drinkable water system in the
event of a depression. This device has a rear
outlet that may liberate innocuous steam during
heating. Do not close or couple the air-break
outlet.
THE GUARANTEE DOES NOT COVER
DAMAGE CAUSED BY INCORRECT
INSTALLATION.
INSTRUCTIONS FOR
THE USER
6. INFORMATION ON THE
WASHING MACHINE
6.1 DESCRIPTION OF THE MACHINE
The machine is composed of the following
main parts:
1) Hood under which the control circuit is
lodged
2) Soap dispenser for pre-wash, wash (foam-
damping washing powder) and liquid
conditioner (foam-damping type)
3) Loading door
4) Coin-meter (on coin-operated machines
only)
5) Coin box (on coin-operated machines
only)
6) Drain (8-11-18: 50 mm; 26-33: 75 mm)
7) Equipotential terminal
8) Air break
9) Water inlets (3/4").
Description of the keypad
Figure 1
1. YELLOW LED: STOP – The wash
cycle is over or the machine has just
been switched on
2. GREEN LED: PREWASH - Prewash
step underway (when scheduled).
3. GREEN LED: WASH - Wash step
underway.
4. GREEN LED: RINSE 1/RINSE 5 –
Rinse underway (any between 1 and 5)
5. GREEN LED: SPIN – Final or
intermediate spin underway (led blinks
when slowing down)
6. Cycle selection PUSH-BUTTON
7. Value decrease PUSH-BUTTON
8. Programming PUSH-BUTTON to
change settings and add pauses
9. Value increase PUSH-BUTTON
10. Time countdown and alarm DISPLAY
11. Temperature DISPLAY, shows real
temperature inside the drum
12. Cycle DISPLAY shows presently
selected cycle
13. Lit DOT shows that the heating is on.
17
6.2 COMPLETE APPLICATION
RANGE
Your washing machine was designed to wash
synthetic fabrics, woollens, cottons and
linens. Choose your cycle by the appropriate
push-button as suggested on the labels
attached to the garments.
6.3 INFORMATION ABOUT THE
ELECTRICAL EQUIPMENT
The built-in electrical equipment is composed
of protection and control devices that are
lodged on a plate, in the upper part of the
machine. The relevant wiring diagrams and
lists are attached further on.
6.4 STATEMENT OF COMPLIANCE
The washing machine described in this
booklet complies with the following
Directives:
The washing machine described in this
booklet complies with the following
Directives and harmonised standards:
73/23 EEC, 93/68 EEC, 89/336 EEC, 92/
31 EEC, 93/68 EEC
EN60335-1, EN60335-2-4, EN60335-2-7,
EN55014, EN61000-3-2, EN61000-3-3,
EN55104.
7. INSTRUCTIONS FOR USE AND
ORDINARY MAINTENANCE
7.1 OPERATION
Make sure that the cold water, hot water and
steam taps are open (the latter applies only to
steam-heated machines).
Turn on the thermomagnetic automatic cir-
cuit-breaker on the wall. Energise the ma-
chine by turning the red switch on the con-
trol panel to position 1. If the door is closed,
the machine will then be ready to be started
using the START push-button on the ma-
chine front panel.
To select the cycle, open the door by the
appropriate handle and press on the "SEL"
push-button. The display will show
programme number: to confirm it just close
the door. Otherwise, press the SEL push-
button again and again until the display
reads the desired cycle number.
After you have chosen your cycle following
the temperature and wash action suggested
by the labels attached to the garments (see
cycles below), sort the laundry according to
the type of fabric, put it into the drum and
close the door. Then fill the various dispenser
compartments with soap (foam-damping
type) according to cycle selection, i.e.: