Nemox gelato pro 1700 Instrucciones Para El Uso página 5

HOW TO CONNECT THE CORD TO A U.K. PLUG: IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
•Green and yellow:
•Blue:
•Brown:
Please, read the instructions given below before connecting the cord to a plug.
If in doubt, please, consult a qualified electrician. As the colours of the wires in
the mains lead of this appliance may not correspond with the coloured
markings identifyng the terminals in your plug, proceed as follows: the wire
that is coloured Green and Yellow must be connected to the terminal in the
plug which is marked with the letter E or the Earth symbol (G), or coloured
Green or Green and Yellow.
The wire that is coloured Brown must be connected to the terminal which is
marked with the letter L or coloured Red. The wire that is coloured Blue must be
connected to the terminal which is marked with the letter N or coloured Black.
SAFETY POINTS FOR REWIRABLE OR MOULDED PLUG
The mains lead of this appliance may be already fitted with a BS1363 13A plug.
•If your socket outlet is not suitable for the plug, then the plug must be removed (cut off if it is a moulded on plug),
the flexible cord insulation should be stripped back as appropriate and a suitable 3 pin plug fitted.
•WARNING: Dispose of a plug that has been cut from the power supply cord, as such a plug is hazardous if
inserted in a live 13A socket outlet elsewhere in the house.
•Should the fuse need to be replaced an ASTA marked fuse, approved to BS 1362, of the same rating must be
used.
•Always replace the fuse cover after fitting a fuse. The plug must NOT be used if the cover is omitted or lost until a
replacement is obtained. Make certain that only the correct fuse cover is used and fitted.
•For plugs with detachable fuse cover, the replacement must be the same as the colour insert in the base of the
plug, or as directed by the embossed wording on the base of the plug.
•If the detachable fuse cover is lost a replacement may be purchased from a Service Centre.
•Information for supply may also be obtained from the plug manufacturer.
ICE CREAM MAKER "GELATO PRO 1700"
The appliance is sold complete with all the
accessories for use with fixed or removable bowl. In
the original package, the removable bowl is stored
inside the fixed bowl.
IMPORTANT ABOUT THE USE
•Hygiene is the most important aspect of ice cream
making. Make sure all the parts, in particular those
coming in direct contact with the ice cream, are
scrupulously clean.
•Never turn off the freezing switch (L) when the
machine is working. In case you accidentally
switch it off or the power fails, wait at least 10
minutes before turning it on again. The compressor
is fitted with a safety device to prevent any possible
damage to the motor unit. Should you restart the
machine immediately after it has been switched off,
the compressor will not freeze.
•The paddle movement and the freezing plant are
indipendent: the (L) button turns ON and OFF the
refrigeration and the (M) button turns ON or OFF
the mixing paddle. To stop the machine, press both
(M) and (L) buttons. After the machine has been
switched off, wait approximately 10 minutes before
making another ice cream.
•Variations in speed and noise during ice-cream
making are also to be expected and in no way
affect the unit's normal functioning. In case the ice
cream become too hard, the motor stops by itself.
English
UK USERS ONLY
Earth
Neutral
Live
A safety device protects the motor from possible
damages. Should not the motor begin to work
again, wait till the motor cools.
•Keep the appliance far enough from walls and
furniture, which might restrict air circulation,
necessary for cooling the unit. It is normal for warm
or hot air to flow from the lateral air vents. The
refrigeration process requires this.
USING THE FIXED BOWL
1). Carefully clean all parts in direct contact with
ingredients. Warning: make sure unit is
unplugged before starting cleaning.
2). Insert the mixing paddle (B) securely into the
drive shaft in the fixed bowl.
3). Lock the paddle in place by screwing
(clockwise) the knob (C) over the shaft.
4). Press the (L) switch to start the cooling. Pre-
cool the machine for 5 minutes.
5). Press (M) switch to start the mixing paddle.
6). Pour the mixture into the bowl. For best results,
it is suggested to pre-mix ingredients in a
separate bowl so as to obtain a smooth, lump-
free mixture. Always use ingredients at fridge
temperature so as to reduce temperature
differences and cut down preparation time.
7). Place the transparent cover (D) on the bowl.
Preparation time varies according to quantity,
temperature of the mix, type of ice cream
5