ELICA NIKOLATESLA SWITCH Uso Y Mantenimiento página 14

Ocultar thumbs Ver también para NIKOLATESLA SWITCH:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 28
3.2.3 Hob features
• Safe Activation: The product is activated only in the presence of
pots on the cooking zone: the heating process does not start or is
interrupted if there are no pots, or if these are removed.
• Pot Detector: The product automatically detects the presence of
pots on the cooking zones.
• Safety Shut Down: For safety reasons, each cooking zone has a
maximum operating time, which depends on the maximum power
level set.
• Residual Heat Indicator: When switching off one or more cooking
zones, the residual heat is indicated with a specific visual signal on
the display of the corresponding zone by the " " symbol.
3.2.4 Operation
Note: activate the required zone first
• Switching on: touch
again to switch off.
• Cooking Zone Selection
the selection bar (3) corresponding with the desired cooking zone.
• Power Level
Touch the selection bar (3) and slide right with fingers to increase
the Power Level, left to decrease.
There are 9 power levels available + an intensive power level
indicated on the display by the " " symbol (Power Booster).
The " " power level (Power Booster) remains active for 5 minutes,
after which the power returns to the previous level.
• Bridge Zones: Cooking Zones FL
("Secondary") and the zones FR
("Secondary") can work as a pair or in combined mode
creating a single zone thanks to the Bridge function (2 in total: 1 on
the right and 1 on the left) with the same power level. This function
allows evenly distributed cooking with large-sized pots and pans.
To activate the Bridge Function:
- select both cooking zones to be used simultaneously
- The Bridge indicator
(21) of the "Secondary" cooking zone
lights up
- using the Selection area (3), of the "Master" cooking zone the
Operating power level can be set
- to disable the Bridge Function all you have to do is to repeat the
activation procedure
• Power Limitation
The Power Limitation function allows for operation of the product to
be set to limit the power consumption (kW)
Note : the setting of the hob must be made with the hob switched off
at the time it is connected to the electrical supply, or when
reconnected to the electrical supply, within 2 minutes, without
pressing the
button.
ON/OFF hob/ extractor system. touch
("Master") and RL
("Master") and RR
To set the Power Limitation:
- touch and hold the
acoustic signal.
- slide simultaneously on the FL and RL selection bars
then press and hold the corresponding area at the last power level
- the Timer (15) display shows the symbols "CF6", to indicate that it
is possible to run the setup
- then press the
display PHA (Phase Power Limit):
: Touch
- to change the Power Limitation settings, slide on the selection
areas FL
. to save the selection made, press the
second; an audible signal will be emitted to confirm the setting and
the function quits.
3.3 Using the extractor system
• Switching on: Touch
system.
Touch again to switch off.
• Switching the extractor system off: Open the Flap ttouch the
Selection bar (6) to activate the extractor system.
Note: The extractor zone is fitted with a mechanical rotating FLAP.
The FLAP must be opened before switching on the hood to activate
the extractor system. The hood has a sensor which when the
extractor is on stops the motor automatically if the FLAP is closed.
Extraction only starts again when the FLAP is reopened.
• Extraction speed (power):
Touch and slide your fingers along the Selection bar (6):
to the right to increase extraction speed (power) (0-8);
to the left to decrease extraction speed (power) (8-0).
The product has an additional 2 timed extraction speeds (power
levels):
"9" for 15 minutes,
"10" for 5 minutes
after that the power returns to level 8
Note: both speeds are indicated on the display (13) of the selected
cooking zone with the " " symbol.
14
buttons until you hear a brief
, from left to right,
until a brief acoustic signal is emitted
button and the display timer (15) will
the FL zone
display shows the current
setting**
0 = 7.4 KW (default setting)
1 = 4.5 KW
2 = 3.1 KW
ON/OFF of the hob/extractor
buttons for 1

Publicidad

Tabla de contenido
loading

Tabla de contenido