Product Parts; Preparing For Installation; Installing The Child Seat In The Vehicle - CYBEX gold SOLUTION S2 I-FIX Guia Del Usuario

PRODUCT PARTS

EN
(1) User Guide Storage
Compartment
(2) Backrest
(3) Booster
(4) ISOFIX Locking Arms
(5) ISOFIX Adjustment Handle
(6) ISOFIX Anchorage Points
(7) ISOFIX Safety Indicator

PREPARING FOR INSTALLATION

Connect the backrest (2) to the booster (3) by hooking the guide lug on the
axis of the booster. The backrest (2) is then folded forward. When taking the
product out of the box, the Linear side-impact protection (9) is activated on
both sides of the seat.
THE CORRECT POSITION IN THE VEHICLE
The child seat can be used on vehicle seats which are equipped with an
automatic three point belt. Please refer to the enclosed vehicle type list
for approved vehicles. You can obtain the most up-to-date version from
www.cybex-online.com.
In case your car is not equipped with ISOFIX connection points, there is
always the possibility to use the SOLUTION S2 i-FIX with retracted ISOFIX
locking arms.
Above a child's stature of 135 cm, the compatibility between the SOLUTION
S2 i-FIX and your vehicle might be reduced. Please review the vehicle type list
to check whether the child seat can be used in all headrest positions without
restrictions.
In exceptional cases, the child car seat may also be used on the front
passenger seat. Always comply with the recommendations of the vehicle
manufacturer.
6
(8) ISOFIX Release Button
(9) Linear side impact protection (L.S.P.)
(10) L.S.P. Operating button
(11) Adjustable Headrest
(12) Headrest Height Adjuster
(13) Lap Belt Guide
(14) Shoulder Belt Guide

INSTALLING THE CHILD SEAT IN THE VEHICLE

1. Always ensure that...
• the backrests in the vehicle are locked in their upright position.
• when installing the child seat on the front passenger seat, it is adjusted as
far back as possible without affecting the belt routing.
2. Use the ISOFIX adjustment handle (5) under the booster (3) and pull the
two ISOFIX locking arms (4) to their furthest extent.
3. Now twist the ISOFIX locking arms (4) 180° so that they are facing the
direction of the ISOFIX anchorage points (6).
4. Place the child seat on the appropriate seat in the car.
5. Push the two ISOFIX locking arms (4) into the ISOFIX anchorage points (6)
until these lock into place with an audible "CLICK".
6. Use the ISOFIX adjustment handle (5) and push the car seat against the
vehicle seat.
7. Ensure that the entire surface of the backrest (2) of the child seat is placed
against the backrest of the vehicle seat.
If the headrest of the vehicle is in the way, pull it upwards to its furthest
��
extent or remove it completely (except in rear-facing vehicle seats).
8. Ensure the seat is secure by trying to pull it out of the ISOFIX anchorage
points (6). The green safety indicators (7) must be clearly visible on both
sides of the seat.
9. In case the seat is used without ISOFIX, it can be stored away on the
bottom of the seat.
By using ISOFIX, a connection to the vehicle is created which increases
��
your child's safety. Your child still needs to be secured with the three-point
belt of the vehicle.
10. If the "Linear Side-impact Protection" (L.S.P.) (9) is in conflict with the car
door or if it affects the space on the passenger seat, it is possible to close the
L.S.P. Press the L.S.P Operating button (10), hold it pressed and fold in the
L.S.P. (9) with slight push. Then, release the L.S.P. Operating button (10).
The car seat can also be used without the L.S.P. in use, if there is not
��
enough space in the vehicle.