Indirect Heat Gas Boiling Pan; Filling The Jacket - AFG 900 Serie Instrucciones Para Instakkacion, Uso Y Manteniniento

Switching on
Turn the energy regulator knob to any position between "1" and
"5".
• The yellow indicator light switches on.
Switching off
Turn the energy regulator knob to position "
• The yellow indicator light switches off
COOKING
• Fill the well.
• Turn the knob to position "1".
• Light the burners.
• Adjust the heating according to your cooking requirements.
When the chosen cooking position is other than "5", heating
is intermittent. It switches on and off automatically. The boiling
intensity of the water may vary visibly, but this has no effect on
cooking. When the heating switches off, the yellow indicator
light switches off too.
AT THE END OF SERVICE
• Switch the heating off.
• Switch the burners off
• Empty the well completely.
• Turn the knob to position "0".

14 INDIRECT HEAT GAS BOILING PAN

REMINDERS FOR USE
• The appliance is designed for cooking and preparing food in
water.
• Do not light the pilot burner or leave it on when there is no
water in the well.
• Do not activate the heating system when there is no water in
the well or in the jacket.
• While the appliance is on, the water level must be maintained
level with or above the minimum level indicated on the wall
of the well.
• Use very fine grained salt, adding it to the well when the wa-
ter is boiling. Do not use coarse-grained rock salt in the well.
• Restore the water level in the jacket every 2/3 working days.
See " FILLING THE JACKET ".
The appliance is equipped with an automatic reset pressure
switch which interrupts heating when steam pressure in the
jacket exceeds optimum levels. Heating restarts when steam
pressure returns to an acceptable level.The intervention of the
pressure switch ensures reduced consumption of water in the
jacket and reduced appliance energy consumption overall.
• At the end of each day, clean the well thoroughly in order to
prevent the formation of corrosive deposits.
The appliance is fitted with a safety thermostat which stops
activation of heating in the event the water in the jacket falls
below the safety level. The red indicator light on the control
panel switches on. Heating will restart after the water level in
the jacket has been restored. See " FILLING THE JACKET ".

FILLING THE JACKET

With the appliance cold, fill the jacket using demineralized wa-
ter.
• Unscrew the anti-depression valve " S2 " from its seat to ac-
cess the jacket filling hole.
• Open the level tap " L ".
• Pour demineralized water into the filling hole.
46
• Stop pouring when water begins to flow from the level tap "
L ".
• Close the level tap " L ".
• Carefully screw back on the anti-depression valve " S2 ".
FILLING AND EMPTYING THE WELL
Filling
".
The control knob has the following positions:
0 Off
(BLUE) Cold water filling
1 Electrical power ON
(RED) Hot water filling
• Open the lid.
• Turn the handle of the front discharge tap clockwise. The tap
is only completely closed when the handle is in the vertical
position.
• Turn the control knob to select hot or cold water for filling.
Water fills from tap on the countertop.
• Fill the well until the water is level with the maximum level in-
dicated on the wall of the well. Do not use the appliance with
the water level above the maximum indicated level.
• To interrupt filling, turn the knob to "0" or "1".
Emptying
Lift and turn the handle of the front discharge tap anti-clockwi-
se. When the tap is open the handle remains in the horizontal
position.
BURNER IGNITION AND EXTINCTION
The gas valve control knob has the following positions
Off
Pilot ignition
Maximum flame
Pilot ignition
Make sure the control knob is turned to "1".
Press and turn the knob to position "
• Press the knob fully down to activate the electronic ignition
and light the pilot burner.
• Hold the knob down for about 20 seconds before releasing it.
If the pilot flame goes out, repeat the operation.
• The pilot flame can be seen through the peep hole on the
control panel.
Main burner ignition
Make sure the control knob is turned to "1".
Press and turn the knob from position "
Switching off
To switch the main burner off, press and turn the knob to posi-
tion "
To switch off the pilot flame, press and turn the knob to position
" ".
".
".
" to position " ".