Preliminary Operations; Electrical Connection - Cuppone Arrotondatrice Guia De Inicio Rapido

Installazione
Installation
Transport
EN
Fig.1.
Fitted with personal protection equipment, transport
the appliance to the installation location.
Use suitable equipment, capable of dealing with its weight:
persons not involved with the appliance installation may not
pass through or stand in the work area during the appliance
assembly.
During the transport, pay particular attention to passing through
openings and/or doors.
rounding machine
Model
weight
RND280
55 kg [121.2 lb]
RND800
86 kg [189.5 lb]

Preliminary operations

Fig.2.
Carefully remove the protective film.
If any glue residue is left on the surfaces, remove it with soapy
water but without any corrosive or abrasive products or sharp or
pointed instruments.
Check that all the parts making up the product are in
good condition and without any faults or breakages, if
that is not the case, contact the Dealer for the procedures
to follow.
Positioning
Fig.3.
Install the appliance in a room:
• dedicated and suitable to the cooking of food;
• having adequate air ventilation;
• containing no flammable or explosive elements;
• that complies with the current regulations on health and
safety and systems in your country;
• is protected from the weather;
• has a maximum temperature of between +5° (41°F) and
+35°C (95°F);
• has a maximum humidity of 70%.
Leave a free space of at least 20 cm between the appliance and
the walls of the room and/or other equipment to facilitate the
use, cleaning and maintenance of the machine itself.
To reduce the risk of a fire,
imum distances
and install the appliances in
not at risk of
rooms and
stallation room must also have a
Serial number plate reading
Fig.4.
The serial number is on the back of the appliance.
It provides important technical information that is vital in case of
a request for maintenance or repair of the appliance: please do
not remove, damage or modify it.

Electrical connection

Before installing the appliance,
comply with the regulations in force
where it is going to be used and
tions indicated on the appliance rating plate
side of the product.
Installation
Instalación
weight of Measurements
packaging + of the rounding
rounding machine machine packaging
64 kg [141 lb]
500 x 750 x 1000 mm
[19.69 x 29.53 x 39.37inc.]
95 kg [209.4 lb]
comply with the stated min-
fireproof
explosion. The floor of the in-
fireproof
surface finish.
check that systems
in the country
with the specifica-
on the LH
Installation
Установка
have the connection cable and the
• single-phase machines
plug already fitted; for the connection, just insert the plug in
a socket of suitable capacity
have the power cable already in-
• three-phase machines
stalled; a plug (not supplied) must be fitted to it
able capacity. This operation must be carried out by qualified
personnel.
For a correct electrical connection, the appliance must:
equipotential system
• be included in an
pliance with the legislation in force. This connection must be
made between the various devices with the terminal marked
with the equipotential symbol
a maximum cross-section of 10 mm
IEC EN 60335-2-42:2003-09) and must be yellow-green;
grounded
• must be
• must be connected to a
the regulations in force (0.03A A type);
• must be connected to an
ing complete disconnection in overvoltage III category con-
ditions.
The Manufacturer accepts no liability for failure to comply with
the above.
If required, the cable can be replaced by the Dealer or its
technical service or by a person with similar qualifications
to prevent any risk.
Supply
Model
V
AC 230V/50Hz
RND 280
AC 3 N 400V/50Hz
AC 230V/50Hz
RND 800
AC 3 N 400V/50Hz
Pre-testing and final inspection
The product is checked and tested in the Manufacturer's plant
before being delivered to the customer.
The "production process check sheet" enclosed with it guaran-
tees that each step in the production process, from assembly to
packaging, was carefully checked from both the operating and
safety standpoints.
Operations to carry out before delivery of the product to the
customer:
Check the installation is correct;
•
Start the appliance
• following the instructions in the "Use and
Maintenance" manual annexed: monitor it during the whole
test and check that all the electrical components work properly.
• At the end of the test, you
IF NOT REGULARLY ACTIVATED, THE VALIDI-
TY OF THE SAME STARTS FROM THE INVOICE
DATE AND NOT FROM THE ACTUAL INSTALLA-
TION DATE.
Provide the user with all the information
•
and safe use of the appliance.
26
Fig.5.
Fig.6.
. The cable must have
(in compliance with
2
to the mains (green-yellow wire);
circuit breaker
in compliance with
omnipolar circuit breaker
Absorbed
Motor Cable type
current
kW n x mm
A
0.37 kW 2.7 3x1.5
0.37 kW 1.8
0.37 kW 2.7
0.37 kW 1.8
MUST
activate the guarantee.
on the correct
of suit-
in com-
allow-
2
4x1.5
3x1.5
4x1.5