Información Transmitida - Roland SP-808EX Manual Del Usuario

Apéndices
02H Number of Bytes
00H "I/F" sub command
nnH Information Field (08H, 09H, 0AH, 0BH, 0CH, 0DH, 0EH, 0FH)
F7H EOX (End of System Exclusive Message)
If the device ID on the message was as same as that of the receiving 10H or 7FH, the
SP-808EX locates the selected time location stored to the specified information field.
❍Format 2—LOCATE [TARGET]
Status Data Bytes
F0H 7FH, Dev, 06H, 44H, 06H, 01H, hrH, mnH, scH, frH, ffH
Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Realtime Header
Dev Device ID (10H or 7FH)
06H MMC Command Message
44H LOCATE (MCP)
06H Number of Bytes
01H "TARGET" sub command
hrH, mnH, scH, frH, ffH
Standard Time with Sub Frame
F7H EOX (End of System Exclusive Message)
If the device ID on the message was as same as that of the receiving 10H or 7FH, the
SP-808EX locates the specified time location received from the command.
G MOVE
Status Data Bytes
F0H 7FH, Dev, 06H, 4CH, 02H, ddH, ssH
Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Realtime Header
Dev Device ID (10H or 7FH)
06H MMC Command Message
4CH MOVE
02H Number of Bytes
ddH Name of the Efficient Destination Information Field
(08H,09H,0AH,0BH,0CH,0DH,0EH,0FH)
ssH Name of the Efficient Source Information Field (01H)
F7H EOX (End of System Exclusive Message)
If the device ID on the message was as same as that of the receiving 10H or 7FH, the
SP-808EX transfers the data on the selected source information field to the destination
Information Field, if the name of both information fields is efficient.
3. Información transmitida
I Mensaje Channel Voice
G Note On/Off
When "Metro." in the SYSTEM parameters(1.Set System Param?) is "MIDI", MIDI note
number/velocity of MIDI channel number which is assigned to the Metronome is
transmitted.
The MIDI Channel number specified in "Pads Tx Ch." in the "1. Set MIDI Param?" System
parameter and the Note number specified in "RxNote(Pad1)" are output.
In this case, Velocity is fixed at 100.
Status Second
9nH mmH
n = MIDI Channel No.: 00H--0FH (ch.1--ch.16) (*1)
mm = Note No.: 00H--7FH (0--127)
ll = Velocity: 01H--7FH (1--127) / 00H = NOTE OFF
* 1Only when transmitting Metronome.
G Control Change
When "Mixer, D-Beam" in the "1. Set MIDI Param?" System parameter is set to "SEND," the
SP-808's mixer parameters are sent via Control Change messages. Also sent is the data from
the D-Beam Controller and the three knob controllers.
Status Second
BnH mmH
201
Status
F7H
Status
F7H
Third
llH
Third
llH
n = MIDI Channel No.: 0AH--0FH (ch.11--ch.16:
mm = Mixer Parameter No.: (see below)
ll = Mixer Parameter Value: 00H--7FH (0--127)
❍ Mixer Parameter and MIDI Channel/Control Change No.
<Mixer Channel Strip>
+———————————————————— Master
| +————————————————— Track A
| | +—————————————— Track B
| | |
| | |
| | |
| | |
MIDI ch. 11 12 13 14 15 16
Level 7 -> -> -> -> ->
Balance 10 -> -> -> ->
Effects Send Level 91 -> -> -> -> ->
AUX Send Level 92 -> -> -> -> ->
<Master Block> MIDI ch. = 11
Level 7
Balance 10
Knob Conroller C1 16
Knob Conroller C2 17
Knob Conroller C3 18
Knob Conroller C4 19
D Beam Controller L 80
D Beam Controller R 81
Effects Send Level 91
AUX Send Level 92
IMensaje System Common
G MIDI Time Code Quarter Frame Messages
MIDI Time Code Quarter Frame Messages can be transmitted while the SP-808EX is
running (Playing or Recording) if the SONG parameter "Sync Src" is "INTERNAL" and
"Sync Out" is "MTC". The transmitted time counts are summed to "MTC Offset Time" as the
song top is "00:00:00:00".
Status Second
F1H mmH (= 0nnndddd)
nnn = Message type: 0 = Frame count LS nibble
1 = Frame count MS nibble
2 = Seconds count LS nibble
3 = Seconds count MS nibble
4 = Minutes count LS nibble
5 = Minutes count MS nibble
6 = Hours count LS nibble
7 = Hours count MS nibble
dddd = 4 bit nibble data: 0H--FH (0--15)
If the upper and lower 4 bits of the count are combined, these bit fields are assigned as
follows.
Frame Count
xxx
yyyyy
Seconds Count
xx
yyyyyy
Minutes Count
xx
yyyyyy
Hours Count
x
yy
zzzzz
G Song Position Pointer
The current position is transmitted with the Song Position Pointer Message before the SP-
808EX starts to run or after the locate operation, when "Sync Src" is "INTERNAL" and "Sync
Out" is "MIDI CLOCK".
see below)
+——————————— Track C
| +———————— Track D
| | +————— MIC/LINE
| | |
->
xxxyyyyy
Reserved (000)
Frame No. (0--29)
xxyyyyyy
Reserved (00)
Seconds Count (0--59)
xxyyyyyy
Reserved (00)
Minutes Count (0--59)
xyyzzzzz
Reserved (0)
Time Code type
0 = 24 Frames/Sec
1 = 25 Frames/Sec
2 = 30 Frames/Sec (Drop Frame)
3 = 30 Frames/Sec (Non Drop Frame
Hours