Fein RSG Ex 1500 A Manual De Instrucciones página 14

en
14
Translation of the Original Instructions.
en
Symbols, abbreviations and terms used.
Symbol, character
!
(**)
Technical Data.
Order number
Design*
Order number
Design*
Voltage ( U )
f
Frequency ( )
Mains supply: 3 ~ (three-phase current) 3 ~ (three-phase current)
No-load speed (n )
0
– Motor
– Application tools
Feed ( f )
Rated power (P)
Power cord length (with plug)
– RSG Ex 1500 (**)
– RSG Ex 18 A/B (**)
Class of protection
Protection class
*Electric motor and auxiliary switch in explosion-proof design (ATEX-compliant)
Design*
Dimensions:
– Weight (m)
– Max. tool Ø
– L
max.
– H
max.
– B
max.
– B
1
– B
2
– B
3
Explanation
Observe the instructions in the text or graphic opposite!
Make sure to read the enclosed documents such as the Instruction Manual and the General Safety Instructions.
Use eye protection during operation.
Use ear protection during operation.
Use protective gloves during operation.
General prohibition sign. This action is prohibited.
Do not reach in!
Do not touch the rotating parts of the power tool.
Do not reach into chains and sprockets!
Warning against sharp edges of application tools, such as the cutting edges of the cutter blades.
Hot surface!
Gripping surface
Additional information.
Confirms the conformity of the power tool with the directives of the European Community.
Worn out power tools and other electrotechnical and electrical products should be sorted separately for environmental-friendly
recycling.
Do not turn or screw the three securing screws.
Applies only for China:
The duration of environmental protection under normal use of the product is 10 years.
May contain numbers and letters
7 360 ...
RSG Ex 1500 A (**) RSG Ex 1500 B (**)
7 360 ...
RSG Ex 18 A (**) RSG Ex 18 B (**)
400 V
50 Hz
2860 rpm
35 rpm
40 mm/min
1500 W
2 x 20 m
2 x 20 m
/I
IP X4
RSG Ex 1500 A (**) RSG Ex 18 A (**)
RSG Ex 1500 B (**) RSG Ex 18 B (**)
80 kg
220 mm
974 mm
334 mm
450 mm
371 mm
201 mm
791 mm
Intended Use of the Pipe Milling Machines.
7 360 ...
The pipe milling machine is intended for cutting and milling free pipe ends and
installed pipe sections made of steel or cast iron, as well as for chamfering pipe ends
7 360 ...
prior to welding them at construction sites or in the open. The pipe milling
machine is for specialty companies and to be operated by specialists; it is not
intended for continuous everyday use.
400 V
The complete pipe milling machine is not approved for explosion-protected areas.
50 Hz
The pipe milling machine is not intended for:
– use in areas with explosive atmospheres.
– use during heavy rain and work under water.
– use outside of the temperature range of -20°C to 40°C.
2860 rpm
– for cutting explosive materials.
70 rpm
– for cutting combustible material.
80 mm/min
EC Directive 94/9EC ATEX (Atmosphères Explosibles)
1500 W
Please note that FEIN pipe milling machines of the type RSG Ex (**) are not
approved for use in explosive atmospheres and therefore no EC type examination
certificates exist for these pipe milling machines in accordance with Directive
2 x 20 m
94/9EC.
2 x 20 m
(Only two ATEX-compliant components are installed on the RSG Ex (**) pipe
/I
milling machines, being the electric motor and the auxiliary switch).
IP X4 The ATEX directive applies only in the EC area.
At a glance.
1 Tightening device
2 Fastening screw for side plate
3 Side plate
4 Information label
5 Bolt
80 kg
6 Threaded spindle
220 mm
7 Feed mechanism
1088 mm
8 Pan head screw for feed mechanism
334 mm 9 Fitting screw
10 Running axle
431 mm
11 Clamping lever
371 mm
12 Hexagon bolt
201 mm 13 Washer
14 Tightening axle
991 mm
15 Nut
16 Tool spindle head