O.FOotrest Height Adjustment; Wheel Locks - Sunrise Medical Zippie ZONE Manual De Instrucciones

E N G L I S H
4. Correcting a Pull to the Right or Left
Determine which direction the chair is pulling (right or left). Make the following adjustments
to the caster on that side of the chair:
a. Loosen the screw (
b. Loosen the screw on the upper spline (
c. Rotate the upper spline to turn the caster fork toward the forward driving direction.
Turn the ring clockwise, and the fork will swing outwards. Turn the ring counterclock-
wise, and the fork will swing inwards.
d. When the caster fork is correctly rotated forward, retighten the screws.
e. After making the desired adjustment, recheck the squareness of the casters. (See
"Checking for Caster Squareness" in Section N).
O. FOOTREST HEIGHT ADJUSTMENT
To adjust the height of your footrest, loosen the screw (B) on both footrest clamps. Slide the
footrest up or down to the new desired height and tighten the two set screws. Use a MAX
torque setting of 62 in-lbs (7 Nm). (Frame damage may occur if overtightened.) It is recom-
mended that you maintain a minimum of 2.0 inches (5 cm) between the lowest point on the
footrest and the floor. This will provide adequate clearance for uneven surfaces and prevent
damage to your footrest.
35
Flip-up Footrest
To adjust the angle of the Flip-up Footrest, loosen two bolts (C) and rotate the footrest angle
stop bracket. Once positioned, retighten bolts (C) to 92 in-lbs. For certain narrow widths,
only one bolt will be present.
High Mount Footrest Mount
1. Loosen all four socket heads (D) on both sides of the chair.
2. Slide footrest to desired height.
3. Tighten socket to 62 in-lbs on both sides.
P . WHEEL LOCKS
Zippie ZONE Adjustable and Zippie ZONE Active Rigid wheelchairs are shipped with one of
five types of wheel locks. Wheel locks are installed at the factory unless you have requested
otherwise.
Use a torque setting of 62 in.-lbs. (7 Nm) when setting up wheel locks.
1. High-Mount Push-to-Lock or Pull-to-Lock
a. Using a 3mm Allen wrench, loosen both side screws (F). Then turn one of the top
screws (E) in the clamp counterclockwise one-quarter turn.
b. Repeat the same process with the remaining screws (E & F).
c. Alternately loosen the screws (two turns each) until all screws are removed.
d. Slide clamp toward the rear wheel until the wheel lock is embedded into the tire to
prevent wheel movement, when in the locked position.
e. Retighten the top screws (E) first, followed by the side screws (F). Tighten screws to
62 in-lbs. (7 Nm).
2. Compact Wheel Locks
a. Using a 3mm Allen wrench, turn one of the screws (E) in the clamp counterclockwise
one-quarter turn.
b. Repeat the same process with the remaining three screws (E & B).
c. Alternately loosen the screws (two turns each) until all four screws are removed.
d. Slide clamp toward the rear wheel until the wheel lock is embedded into the tire to
prevent wheel movement, when in the locked position.
e. Adjust angle position.
f. Tighten screws to 62 in-lbs. (7 Nm).
NOTE– Clamp and wheel lock may need to be rotated to clear frame tubing.
116100 Rev. B
All manuals and user guides at all-guides.com
31 33
31
-D) inside the caster tube using a custom 6mm Allen wrench.
33
-A).
36
37
Wheel Locks Adjustment
38
34 35 36
20
33
A
34
B
35
C
36
D
E 37
F
E
38
F
I X .