Hunter ProAlign PT200 Instrucciones Funcionamiento página 9

are used with the front or rear sensors of another set, "Zero Only" calibration
must be performed on the new set.
The calibration procedures must be followed carefully. An accurate calibration
will not be obtained if procedure performance is rushed.
Remote Indicator (LED) Remote Indicator (LED)
The LED Remote Indicator allows the technician to be "mobile" in the bay
while making adjustments to the vehicle.
Remote Control Transmitter Remote Control Transmitter
If the remote control transmitter fails to operate properly, the battery may have
to be replaced. A nine-volt alkaline battery is required.
An alkaline battery is required to provide the proper current for
remote transmitter operation.
Software Identification Software Identification
The "Identify Software" screen allows you to identify the software currently
installed on the system.
This screen does not necessarily reflect your software.
It is displayed by pressing "Identify Software" on the "Reset" screen. The
contents of the screen are self-explanatory.
Removal and Installation of USB Flash Removal and Installation of USB Flash
Drives Drives
Turn the unit power off and disconnect the AC power cord from the console.
Access the rear of the PC by removing the rear console cover. The
recommended arrangement of USB Flash Drives is below.
A) Power
C) Mouse
E) Data Drive
G) Audio Jack
I) Keyboard
Remove the installed USB drive from the PC.
Insert the new USB drive into the PC.
Reinstall the console cover.
Re-attach the AC power cord to the console.
Electronic Key Electronic Key
If the USB program drive is installed into a PT200 unit without the proper key
being inserted in the board, an error message will appear.
Replacing the Electronic Key
Turn the unit power off and disconnect the AC power cord from the console.
Access the USB electronic assembly at the rear of the console.
Remove the four screws to open the back cover of the USB electronic
assembly.
A) Key sockets
Install the keys.
Re-install the USB electronic assembly cover.
Re-attach the AC power cords and cables to the console.
End User License Agreement End User License Agreement
Use of equipment and it's operating software is acknowledgment of
agreement to the terms of the End User Licensing Agreement ("EULA"). The
entire EULA can be found by scanning the QR Code below.
English
Image 2.
Image 3.
B) Monitor cable
D) Program Drive
F) Logging drive
H) USB Box
Image 4.
B) Board 45-1359-1
Environmental Information Environmental Information
The following disposal procedure shall be exclusively applied to the machines
having the crossed-out bin symbol on their data plate.
This product may contain substances that can be hazardous to the
environment and to human health if it is not disposed of properly.
The following information is therefore provided to prevent the release of these
substances and to improve the use of natural resources.
Electrical and electronic equipment should never be disposed of in the usual
municipal waste but must be separately collected for their proper treatment.
The crossed-out bin symbol, placed on the product and on this page, reminds
the user that the product must be disposed of properly at the end of its life.
In this way it is possible to prevent that a non specific treatment of the
substances contained in these products, or their improper use, or improper
use of their parts may be hazardous to the environment or to human health.
Furthermore, this helps to recover, recycle and reuse many of the materials
contained in these products.
Electrical and electronic manufacturers and distributors set up proper
collection and treatment systems for these products for this purpose.
At the end of the product's working life, contact your supplier for information
about disposal procedures. When you purchase this product, your supplier will
also inform you that you may return another worn-out appliance to him free of
charge, provided it is of the same type and has provided the same functions
as the product just purchased.
Any disposal of the product performed in a different way from that described
above will be liable to the penalties provided for by the national regulations in
force in the country where the product is disposed of.
Further measures for environmental protection are recommended: recycling
of the internal and external packaging of the product and proper disposal of
used batteries (only if contained in the product).
Your help is crucial in reducing the amount of natural resources used for
manufacturing electrical and electronic equipment, minimise the use of
landfills for product disposal and improve the quality of life, preventing
potentially hazardous substances from being released in the environment
Image 5.
9