Polisport MOVE JOY CFS Manual De Instrucciones página 4

EN
REAR CHILD SEAT FOR BICYCLE
ATTENTION
This product contains small parts like bolts, plastic bags, and small packaging hangers. Keep them out of reach of children to avoid suffocation hazards.
TABLE OF CONTENTS OF PRODUCT
A. MAIN SEAT
B. RETENTION SYSTEM HARNESS
B1. SAFETY BUCKLE
B2. HEIGHT STRAP ADJUSTERS
B3. CENTRAL STRAP ADJUSTERS
B4. SHOULDER PADDINGS
B5. RETENTION SYSTEM ADJUSTMENT HOLE
SPECIFIC INSTRUCTIONS FOR MOUNTING
• This child bicycle seat must not be mounted in folding bicycles.
• This child bicycle seat must not be used on EPAC / Pedelecs above 25 km/h
/ 15,5mph.
• This child bicycle seat must not be mounted to bicycles fitted with rear
shock absorbers.
• This child bicycle seat must not be mounted to motorized vehicles such as
mopeds, scooters.
• The child bicycle seat must be assembled on a carrier with a load capacity
of 27kg, according to the EN ISO 11243:2016 standard.
• The maximum weight applied to the carrier cannot exceed 27kg, according
to the EN ISO 11243:2016 standard.
• For safety reasons this seat shall only be fitted to luggage carriers in
accordance with EN ISO 11243:2016 - 125 to 175 mm.
• The child bicycle seat must be assembled on bicycles with wheels with
diameters of 26", 27,5", 28" and 29".
• This child bicycle seat is only suitable for carrying children with a maximum
weight of 22 Kg, and a maximum height of 110 cm, (and children with
recommended ages ranging from 9 months to 6 years of age - with the
weight and height as the decisive variable).
• The total weight of the cyclist and the child transported must not exceed
SPECIFIC INSTRUCTIONS FOR MOUNTING THE SEAT IN THE BICYCLE
1. Unscrew the hand knob (G1), while simultaneously lifting the security ring
(G2). Open the jaw (G3) to an aperture wider than the luggage carrier.
2. Pull the safety belt for the bicycle frame (C) upwards. Make sure it does not
interfere with mounting the seat to the bicycle.
3. Place the seat on the luggage carrier and then fasten the hand knob (G1)
so that the seat remains slightly attached to the luggage carrier.
4. The child seat has a centre of gravity (F) (inscribed on the child seat) that
must be positioned in front of the rear wheel axle. If it is positioned behind
the axle, the distance must not exceed 10 cm. Special care must also be
taken when positioning the child seat to ensure that the cyclist does not
touch the child seat with his feet when cycling. Note: In Germany, according
to the German Traffic Law StVZO, bicycle seats may only be fixed so that 2/3
of the seat depth or the Gravity Center of the seat is located between the
HOW TO SAFELY PLACE AND SECURE THE CHILD ON THE SEAT
8. To safely place the child on the seat you must place the bicycle on flat and
solid ground for maximum bicycle stability. Even if your bicycle offers robust
quick stands, you must always hold the bicycle, while placing/ removing the
child. You must carry your child in your lap and safely place him on the seat.
C. SAFETY BELT FOR BICYCLE FRAME
C1. SAFETY BELT BUCKLE
C2. SAFETY BELT RETAINER
D. TRACEABILITY INFORMATION
E. FOOTREST
E1. FOOTREST LEVER
E2. FOOTREST STRAP
the maximum permitted load permitted for the bicycle. Information on the
maximum load can be found in the operating instructions of the bicycle. You
can also contact the manufacturer for this question.
• This child bicycle seat can be used on EPAC / Pedelecs up to 25 km/h /
15,5 mph.
• The seat may only be mounted on a bicycle suitable for the attachment
of such additional loads. Please consult your bicycle or lugagge carrier
instructions manual.
• The position of the child bicycle seat must be adjusted so that the bicycle
rider does not touch the child bicycle seat with the feet when in motion.
• It's very important to adjust correctly the seat and its component parts for
optimum comfort and safety of the child. It's also important that the seat
does not slope forward, so that the child does not tend to slide out of it. It is
also important that the backrest slope backward slightly.
• Check if all parts of the bicycle function correctly with the child bicycle
seat mounted.
• Check the instructions of the bicycle, and If you have any doubts on fitting
the child bicycle seat to your bicycle, please contact your bicycle supplier for
further information.
front and rear axle of the bicycle. The seat shall be installed as close to the
saddle as possible.
5. Fasten the hand knob (G1) so that the seat is well attached to the luggage
carrier. As soon as the hand knob is well tightened, make sure the security
lever is properly held as shown in the picture.
6. We suggest shaking the seat to make sure it´s properly and securely
attached to the luggage carrier. This extremely important for cyclist and child
safety.
7. Start to open the safety belt buckle (C1) and pass it around the bicycle
frame. Adjust the belt it as shown in the picture, under tension. Make sure
that remain loosen belt is not in contact with the wheel, so pass it trough the
Safety belt retainer (C2). This step is extremely important for child and
cyclist safety.
It´s forbidden for the child to climb alone on the bicycle or using the
footrests to reach the seat.
9. To place the child in the seat, first fully extend the retention system
harness (B), sliding all the strap adjusters (B2) - this makes it easier to put the
#polisportmove #polisportmove
4 4
F. CENTER OF GRAVITY
G. CARRIER MOUNTING SYSTEM
G1. HAND KNOB
G2. SAFETY RING
G3. JAW