Publicidad
OBJ_BUCH-3181-006.book Page 28 Thursday, April 12, 2018 9:20 AM
28 | English
Briefly pressing the measuring button 2 [
09.06.2017
13:20:23
interrupts the continuous measurement. The
0.0º
1.291
m
current measured value will be shown at the
min
11.623
m
max
bottom of the display. The maximum and mini-
11.623
m
mum measured value appear above it. Pressing
the measuring button 2 [
starts the continuous measurement.
Continuous measurement automatically switches off after
5 mins.
Area Measurement
Select the area measurement
Then measure the width and length one after the other as with
a length measurement. The laser beam remains switched on
between the two measurements. The distance to be meas-
ured flashes in the display for area measurement
play element j).
The first measured value is shown at the top of
09.06.2017
13:20:23
the display.
0.0º
4.640
m
After the second measurement has been com-
9.279
m
pleted, the area will be automatically calculated
43.050 m
2
and displayed. The end result is shown at the
bottom of the display, while the individual
measured values are shown above it.
Volume Measurement
Select the volume measurement
Then measure the width, length and depth one after the other
as with a length measurement. The laser beam remains
switched on between the three measurements. The distance
to be measured flashes in the display for volume measure-
ment
(see display element j).
The first measured value is shown at the top of
09.06.2017
13:20:23
the display.
0.0º
4.640
m
After the third measurement has been complet-
9.279
m
ed, the volume will be automatically calculated
13.919
m
599.276 m
3
and displayed. The end result is shown at the
bottom of the display, while the individual
measured values are shown above it.
Indirect Distance Measurement
Select the indirect distance measurement
There are four measuring functions available for the indirect
distance measurement, each of which is capable of determin-
ing different distances.
The indirect distance measurement is used to measure dis-
tances that cannot be measured directly because an obstacle
would obstruct the laser beam or no target surface is available
as a reflector. This measuring procedure can only be used in
vertical direction. Any deviation in horizontal direction leads
to measuring errors.
Note: Indirect distance measurement is always less accurate
than direct distance measurement. Depending on applica-
tion, greater measuring errors are possible than with direct
distance measurement. To improve the measuring accuracy,
we recommend using a tripod (accessory).
1 609 92A 4F4 | (12.4.18)
],
The laser beam remains switched on between the individual
measurements.
a) Indirect Height Measurement (see figure B)
Select the indirect height measurement
Ensure that the measuring tool is at the same height as the
] once more, re-
lower measuring point. Then tilt the measuring tool around
the reference level and measure the distance "1" as for a
length measurement (displayed as a red line).
09.06.2017
13:20:23
45º
.
b) Double indirect Height Measurement (see figure C)
(see dis-
The measuring tool can indirectly measure all distances,
which lie in the vertical level of the measuring tool.
Select the double indirect height measurement
Measure distances "1" and "2" in this sequence as for a
length measurement.
09.06.2017
13:20:23
30º
.
Pay attention that the reference plane of the measurement
(e.g. the rear edge of the measuring tool) remains exactly at
the same location for all individual measurements within a
measuring sequence.
c) Indirect Length Measurement (see figure D)
Select the indirect length measurement
Pay attention that the measuring tool is positioned at the
same height as the sought measuring point. Now, tilt the
measuring tool around the reference plane and measure dis-
tance "1" as for a length measurement.
09.06.2017
13:20:23
60º
.
d) Trapezium Measurement (see figure E)
The trapezium measurement can be used to determine the
length of a roof slope, for example.
Select the trapezium measurement
Measure distances "1", "2" and "3" in this sequence with a
length measurement. Pay attention that the measurement of
distance "3" starts exactly at the end point of distance "1"
and that a right angle exists between distances "1" and "2" as
well as between "1" and "3".
Upon completion of the measurement, the re-
sult for the sought distance "X" is displayed in
37.116
m
the result line a. The measuring values for the
45.0
distance "1" and the angle "α" are displayed in
26.245 m
the measured-value lines h.
Upon completion of the measurement, the re-
sult for the sought distance "X" is displayed in
48.873
m
the result line a. The measuring values for the
56.335
m
distances "1", "2" and the angle "α" are dis-
35.5
º
32.852 m
played in the measured-value lines h.
Upon completion of the measurement, the re-
sult for the sought distance "X" is displayed in
153.104
m
the result line a. The measuring values for the
60.0
distance "1" and the angle "α" are displayed in
76.552 m
the measured-value lines h.
.
.
.
.
Bosch Power Tools
Publicidad
