Yoto YT-23300 Manual De Instrucciones página 15

PRODUCT OVERVIEW
The oil compressor is used to compress atmospheric air. The compressor can supply pneumatic tools, e.g. a blow, pumping, or
paint spray gun. The correct, reliable, and safe operation of the device depends on its proper use, therefore:
Read the entire instructions manual before the fi rst use of the product and keep it for future reference. If you pass the
product on to others, please pass it on together with the instructions. The instructions manual should be stored near the
device at all times and be available to the operator.
The supplier shall not be held liable for any damage or injury resulting from improper use of the product, failure to observe the
safety regulations and recommendations of this instructions manual. Maintenance activities not described in the instructions man-
ual, changes to the mechanical and electrical design, and other modifi cations cause the loss of the warranty rights, as well as the
rights under the statutory warranty by the user.
PRODUCT ACCESSORIES
The product is supplied complete, however, assembly or appropriate setting is required as described later in this instructions
manual.
TECHNICAL DATA
Parameter
Part No.
Rated voltage
Rated frequency
Short-circuit current
Load current
Rated power
Rated motor rpm
Tank capacity
Rated pressure
Pumping capacity (max. compression)
Noise level
- sound pressure L ± K
pA
- power L ± K
wA
Weight
Insulation class
Protection rating
The declared noise emission value has been measured using the standard test method and can be used to compare one tool to
another. The declared noise emission value can be used in the preliminary exposure assessment.
Caution! Safety measures to protect the operator, which are based on an assessment of emission exposure under actual con-
ditions of use (including all parts of the work cycle, such as the time when the tool is turned off or idle and the activation time),
must be specifi ed.
SAFETY INSTRUCTIONS
Learn how to operate the device. Do not start working or charging before reading the instructions manual. Following the guidelines
contained in the instructions manual reduces the risk of injury, electric shock or fi re.
The device is designed for indoor use only and should not be exposed to precipitation.
The device is not intended for use in potentially explosive atmospheres in highly humid and dusty environments. The temperature
at the workplace should be within the range of +5
should not be operated near places where water is sprayed.
Operating the device at too low a temperature can cause the lubricants to lose their properties and not provide proper lubrication
of the device's systems. Operation at temperatures below 0
During a cold start-up, high oil viscosity, clogged oil fi lters, or malfunctioning valves can cause an oil shortage.
Place the device only on a hard, even and fl at surface.
Make sure that the ventilation openings in the device housing are not obstructed during and after operation.
During operation, some elements of the housing may become hot – touching them may cause burns. It is forbidden to use the
compressor without safety guards. For transporting the device use only its handle. The device must be turned off before trans-
O R I G I N A L
EN
Unit
YT-23300
[V~] 230-240
[Hz] 50
[A] 36
[A] 6.2
[W] 1500
[min ] 2850
-1
[l] 24
[MPa / bar / PSI] 0.8/8.0/116
[l/min] 200
[dB(A)] 74.2 ± 3.0
[dB(A)] 93.7 ± 2.23
[kg] 23
I
IP20
O C to +40 O C, and the relative humidity should not exceed 80%. The device
C can lead to the freezing of condensate inside the tank. Warning!
O
I N S T R U C T I O N S
Value
YT-23305 YT-23310
230-240 230
50 50
36 57
6.2 9.5
1500 2200
2850 1100
50 100
0.8/8.0/116 1.0/10.0/145
200 360
74.2 ± 3.0 74.2 ± 3.0
93.7 ± 2.23 93.8 ± 2.28
31 70
I I
IP20 IP20
YT-23320
230
50
57
9.5
2200
1100
200
1.0/10.0/145
360
74.2 ± 3.0
93.8 ± 2.28
108
I
IP20
15