Publicidad
1.- INTRODUCTION AND GENERAL ASPECTS
This manual has been written by the manufacturer and forms an integral part of the basic equip-
ment supplied with the machine.
This manual provides information that the operator should be aware of and that will enable safe
use of the machine.
SYMBOLS USED IN THE MANUAL
Indicates a dangerous operation for people and/or proper operation of the machine.
Reading the user manual is obligatory.
The safety rules expressed in this manual MUST be followed, especially when using
or maintaining the machine.
This manual MUST be read carefully before using the machine.
Keep this manual in a safe place for as long as you have the machine and ensure that it is always
available to the operator.
1.1 OVERVIEW
The Ecco Automatic duplicator machine has been designed to meet European Regulations (EC).
Solutions have been applied to the design that seek to eliminate risks for the operator when using
the machine: transport, adjustment, use and maintenance. The following instructions should be
followed to ensure proper key duplication:
• Follow the procedures defined in this manual.
• Always use Original JMA Parts.
• Use JMA key blanks.
• Send the machine to an authorised JMA Customer Service Centre for regular servicing (a list
can be found at the end of this manual).
IMPROPER USE
The machine must be installed and used according to the instructions contained in this manual.
The manufacturer accepts no liability for any material damage or personal injury if the machine
is used improperly and any improper use will void all guarantees to which the machine may be
subject.
1.2 TRANSPORT AND PACKAGING
The machine comes inside a cardboard box with the following dimensions:
Width = 570 mm; Height = 520 mm; Depth = = 410 mm .
Machine weight (packaging included) = 22 Kg.
When unpacking the machine, check carefully for any damage during transport.
If you find something out of the ordinary, immediately notify the carrier and do nothing with
the machine until the carrier's agent has performed the corresponding inspection.
To move the machine from one place to another, only lift the machine by the base and
not by any other parts.
The machine must always be transported in its original packaging to ensure its physical
integrity.
1.3 IDENTIFICATION LABEL
The Ecco Automatic key cutting machine comes with an
identification label that indicates the serial or machine
registration number, the name and address of the
manufacturer, the CE mark and the year of manufacture.
2. SAFETY MEASURES
2.1 REGULATIONS
The Ecco Automatic duplicator machine and its safety devices are compliant with Directive
2006/42 EC on Machinery.
This manual cites all the safety regulations that the user must respect when installing and ope-
rating the machine. Failure to follow these instructions may compromise the safety conditions
provided for during design and testing.
10
When used for the purpose for which they have been designed, all machines bearing the CE mark
are compliant with EU Directive 2006/42 EC on Machinery.
The machine operator must know and follow the instructions provided in this manual.
2.2 SAFETY DEVICES
The Ecco Automatic duplicator machine is fitted with safety and other protective devices that
define the user operation area in order to guarantee their safety.
2.2.1 USER PROTECTION
• Earthing connection.
• CIRCUIT BREAKER. This device stops the flow of electricity in the event of the following: If the
electricity supply suddenly fails and prevents the cutter from rotating, the circuit breaker prevents
the cutter from suddenly moving again if electrical power unexpectedly returns and thereby pre-
vents any risk this may pose to user integrity. If this happens, the machine must be manually
switched off and on again by using the power switch.
• Anti-swarf screen. The operator must still wear safety goggles even though this device is pre-
sent.
• Enclosure for the lower section of the machine, preventing access to the interior. This elimina-
tes any risk of entrapment with moving parts of the machine.
• Machine start-up requiring simultaneous interaction with two buttons. This eliminates any risk
of entrapment when starting the automatic cutting cycle.
2.2.2 PERSONAL PROTECTION EQUIPMENT
When operating or maintaining the Ecco Automatic machine, users must wear the following per-
sonal protection equipment:
• CLOTHING: Those responsible for maintaining and operating key duplicator machines should
wear protective clothing that meets all the basic safety requirements currently in effect. On wet
floors, users should wear safety shoes with a non-slip sole.
• SAFETY GOGGLES: The operator should wear safety goggles over the eyes during the duplica-
tion stages of operation.
2.2.3 SAFETY SIGNS AND SYMBOLS
The Ecco Automatic duplicator machine uses the following safety signs and symbols:
Safety goggles must be worn
Read the instruction manual before using the machine
WARNING! Hazardous operation
WARNING! Rotating tool
WARNING! Electrical voltage
Earthing connection
2.2.4 GENERAL SAFETY INSTRUCTIONS
Never disconnect the Earthing connection and make sure it is always connected
correctly.
• Always disconnect the power supply before carrying out any maintenance or cleaning.
• Always disconnect the power supply when the machine is not in use.
• Check the condition of cables regularly. If they are worn or damaged, replace them immediately.
• Keep all electrical connections safe from water and other liquids.
• Do not pull violently on the electrical power cord.
• Ensure that the electrical power cord does not come into contact with oils, sharp objects or
heat.
• During the duplication stages, always keep your hands on the carriage assembly motion con-
trols.
• Always work with dry hands free of grease and oil.
• Do not use the machine in hazardous, damp or wet locations.
• Everyone, and especially children, should keep a safe distance to prevent contact with the
machine and the electrical cables.
2.3 RESIDUAL RISKS
The Ecco Automatic duplicator machine has been designed with the utmost care to ensure it is
safe during transport, adjustment, duplication and maintenance. Nonetheless, it is impossible to
eliminate all risks, whether for technological reasons or for issues related to use of the machine
(excessively complex operations). Therefore, the following residual risks should be taken into con-
Publicidad
