Publicidad
Idiomas disponibles
Idiomas disponibles
B
Using the appliance
Extra Drying
To dry dishes more completely. ( It can only be used with
Hygiene, Universal, ECO, Glass, 58 min )
Strong wash
To wash very dirty, hard to clean dishes. ( It can only be used
with Hygiene, Universal, ECO, Glass, 58 min )
Turbo speed+
Reduce the program time. ( It can only be used with Hygiene,
Function
9
Universal, ECO, Glass, 58 min, Self-cleaning )
indicator
Auto open
After washing the door will open automatically to achieve
better drying effect (Rapid and self-cleaning programs don't
have this function.)
When you press the button for 3 seconds, the button will
light on when a certain program is selected. You can cancel
the auto-open function for 3 seconds again, corresponding
indicator will go off.
Upper
When you select Upper, only the dishes in the upper rack will
be washed. The spray system of the lower basket will not
operate.
Alt
10
indicator
Lower
When you select Lower, only the dishes in the lower rack will
be washed. The spray system of the upper basket will not
operate.
Water softener
• The water softener must be set manually, using the water hardness dial.
• The water softener is designed to remove minerals and salts from the water, which would
have a detrimental or adverse effect on the operation of the appliance.
• The more minerals there are, the harder your water is.
• The softener should be adjusted according to the hardness of the water in your area.
• Your local Water Authority can advise you on the hardness of the water in your area.
24
EN
B
Using the appliance
Adjusting salt consumption
• The dishwasher is designed to allow for adjustment in the amount of salt consumed based
on the hardness of the water used. This is intended to optimise and customise the level of
salt consumption.
• Please follow the steps below for adjustment in salt consumption.
1. Open the door, switch on the appliance;
2. Within 60 seconds after the appliance was switched on, press the Program button ">" for
more than 5 seconds, then enter the water softener setting mode.
3. Press the '>' button again to select the proper set according to your local environment, the
setting will change in the following sequence: H3->H4->H5->H6->H1->H2;
4. Without operation in 5 seconds or press the Power button to complete the setup and exit
the setup mode.
WATER HARDNESS
German
French
British
Mmol/l
°dH
°fH
°Clarke
0 - 5
0 - 9
0 - 6
0 - 0,94
6 - 11
10 - 20
7 - 14
1,0 - 2,0
12 - 17
21 - 30
15 - 21
2,1 - 3,0
18 - 22
31 - 40
22 - 28
3,1 - 4,0
23 - 34
41 - 60
29 - 42
4,1 - 6,0
35 - 55
61 - 98
43 - 69
6,1 - 9,8
1°dH=1.25 °Clarke=1.78 °fH=0.178mmol/l
The factory setting: H3
Every cycle with a regeneration operation consumes additional 4.0 litres of water, the
1)
energy consumption increases by 0.06 kWh and the program extents by 10 minutes.
NOTE
Please check the "Loading The Salt Into The Softener", if
your dishwasher lacks salt.
25
Regeneration
Salt
Water softner
occurs every
consumption
level
X program
(gram/cycle)
sequence
1)
No
H1
0
regeneration
H2
10
9
H3
5
12
H4
3
20
H5
2
30
H6
1
60
EN
Publicidad
