3M PELTOR WS ALERT XP Manual Del Usuario página 12

E:10 Wind shield (foam)
E:11 Charging jack (stainless steel)
E:12 Cup supporting arm (stainless steel)
6. SETUP
6.1. GENERAL
The following points covers the main actions to make the
product ready for operation.
6.2. REMOVE AND INSTALL BATTERIES
(Figure. 1)
Make sure you have read and understood the contents of
Chapter 2. Safety before replacing the battery/batteries.
1. Detach the latch on the left cup with your fingers.
2. Open the cup.
3. Insert or replace the batteries. Make sure the polarity
corresponds to the markings.
4. Close the cup and lock the latch.
6.3. CHARGE BATTERIES
Make sure you have read and understood the contents of
Chapter 2. Safety before charging the batteries.
1. Connect the 3M™ PELTOR™ FR09 connector to the
charging jack (E:11) on the cup.
2. Connect the other USB connector to 3M™ PELTOR™
FR08 power supply.
3. LED indicator on FR09 shows status of the battery when
connected to power.
For more information read and understand the User
Instruction for FR09.
NOTE: Change the battery type if you are switching from
rechargeable to non-rechargeable, see "Configuring your
headset".
7. FITTING INSTRUCTIONS
Inspect the hearing protector before each use. If damaged,
select an undamaged hearing protector or avoid the noisy
environment.
7.1. HEADBAND
(Figure. F:1-F:3)
F:1 Slide out the cups and tilt the top of the shell out, as the
cable must be on the outside of the headband.
F:2 Adjust the height of the cups by sliding them up or down
while holding the headband in place.
F:3 The headband should be positioned across the top of the
head as shown and should support the weight of the headset.
7.2. CARRIER ATTACHMENT
(Figure. F:4-F8)
F:4 Insert the carrier attachment in the slot on the carrier and
snap it into place (F:5).
F:6 Work mode: Press the headband wires inwards until you
hear a click on both sides. Make sure that the cups and the
headband wires do not press on the edge of the carrier when
in work mode as this could reduce the noise attenuation of
the earmuff.
F:7 Ventilation mode: To switch the unit from work mode to
ventilation mode, pull outward on the ear cups until you hear
a click. Avoid placing the cups against the carrier (F:8) as this
prevents ventilation.
7.3. MICROPHONE
(Figure. G:1-G2)
To maximize the performance of the speech microphone in
noisy areas, position the microphone very close to your
mouth (less than 3 mm or 1/8 inch). See figure G:1 and G:2.
8.
8.1. POWER ON/POWER OFF
(Figure. 2)
Long press (~2 s) the Power button to power the headset
on or off.
A voice message will notify "Power on" or "Power off".
The first time the headset is powered on, it automatically
enters pairing mode.
NOTE: If no button has been pressed for 4 hours, the
headset will automatically be powered off. A voice
message will notify "Automatic power off".
8.1.1. OPERATION TIME
Approximate operation time with new AA alkaline batteries
and fully charged LR6NM rechargeable batteries (2100 mAh):
- FM radio and level-dependent: approx 58 hours
- Bluetooth
NOTE:
battery age/condition, the operation time may vary.
8.2. LEVEL-DEPENDENT MICROPHONE FOR
Helps protect your hearing from potentially harmful noise
levels. Constant rumbling and other potentially harmful
noises are reduced to a level below 82 dB, but you can
still speak normally and make yourself heard.
8.3. COMMUNICATION FACE TO FACE
(Figure. 4)
The Push-To-Listen feature enables you to instantly listen
to your environment by muting the FM radio and
Bluetooth
dependent microphones. Short press (~0,5 s) the Power
button two times to activate Push-To-Listen. Short press
any button to deactivate Push-To-Listen.
** 3M™ PELTOR™ WS™ ALERT™ XPI Headset
OPERATING INSTRUCTIONS
streaming and level-dependent: approx 78 hours
®
Depending on the environment, temperature, and
AMBIENT LISTENING
(PUSH-TO-LISTEN, PTL)
audio volume and activating the level-
®
EN
15