Dyson AB09 Manual Del Propietário página 16

EN
LOOKING AFTER YOUR DYSON AIRBLADE TAP HAND DRYER
CAUTION:
This product is not to be used in sinks where a plug is fitted. Before engaging the water flow ensure that the
plughole is clear of any obstructions and that water can drain freely.
HOw TO USE
1. Place your hands beneath the centre of the tap and water will flow automatically for as long as the hands remain in
place.
2. Place your hands to either side of the centre tap to activate the hand dryer, creating sheets of air to scrape water from
your hands.
3. Move your hands backwards and forwards slowly through the air, turning them over so both back and front are
exposed to the airflow.
TROUBLESHOOTING GUIDE
Problem
The Dyson hand dryer fails to start.
The hand dryer is turning on and off erratically.
The hand dryer sometimes cuts out when in use but resumes operation
after a period of time.
The dry time of the hand dryer has increased.
The air flow from the hand dryer is running hotter than usual.
Air is continuously running from the hand dryer.
There is no air coming from the hand dryer.
TAP:
Problem
Water is continuously coming from the tap.
There is no water coming from the tap.
The water coming from the tap is overly hot or cold.
If you have any further questions please contact the Dyson Helpline.
CLEANING
The hand dryer should be cleaned daily.
Follow these 2 simple steps to ensure the unit performs to its best and remains hygienic. Using the wrong cleaning
method or product may invalidate your guarantee.
1. Fit the cleaning cap, and wipe all surfaces with a soft cloth and non-abrasive cleaner. Particular attention should be
paid to the seals of the unit.
2. Clean the air inlets on the base of the motor bucket REGULARLY.
Action
Check fuse/circuit breaker is working and that the power and water supply
are connected.
Ensure the cleaning cap is removed and that the sensors are clean and
unobstructed.
Turn the unit on and off.
Ensure sensors are clean.
Check that the sensor cable from the tap is securely connected.
Check the air inlets are clean and free of dust. If the air inlets are dusty
simply remove dust.
Ensure that the air inlets are free from obstructions and have sufficient
clearance (see installation instructions).
Inspect the air inlets for dust and remove. Inspect filter and change if
required.
Ensure that the hose is securely attached to the base of the tap and no
leaks are present.
Ensure sensors are clean and free from any obstructions.
Check fuse/circuit breaker is working and that the power is connected.
Ensure that the air hose is securely attached to the base of the tap and no
leaks are present.
Check that the sensor cable from the tap is securely connected.
Action
Ensure sensors are clean and free from any obstructions
Ensure that the power and water supplies are turned on and that the
isolation valve is open.
Ensure that the aerator is free from debris, remove and clean / replace if
necessary.
Contact the Dyson Helpline.
GENERAL ADvICE
All cleaning chemicals should be used exactly as indicated by the manufacturer's instructions (including appropriate
dilution).
Any chemicals intended for use should first be tested on an inconspicuous area to confirm suitability.
Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming into contact with the unit,
in particular oils and alcohol-based products.
Ensure that the plughole in your sink is free from blockages and that the water can drain freely.
CHEmICAL GUIDELINES
Many professional cleaning chemicals can be used. The following are some that are harmful to the unit and should not
be used. Use of these will invalidate your guarantee.
Do not use:
Alcohol-acid mixes
Alcohol
Solvent /oil-based products
Quaternary ammonium
Alkali-bleach mixes
Foaming ingredients
Bleach or abrasive cleaners
Do not pressure wash
wATER GUIDELINES
This hand dryer has an IP35 certification.
Use of pressure washers can force water inside the casing. Water damage caused by incorrect cleaning will invalidate
your guarantee.
SOLENOID REPLACEmENT GUIDELINES
It may be necessary to replace the solenoid on your hand dryer. If you suspect this is the case, please contact the
Dyson Helpline.
When replacing the solenoid, the hand dryer must be disconnected from the mains electricity and water supply.
Failure to do so could lead to serious injury and/or damage to property.
FILTER mAINTENANCE
Regularly check the air inlets to ensure that they are free from dust and debris. Simply wiping the inlets with a soft cloth
should be sufficient to remove dust and debris.
If the air inlets get clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed to change your unit's
HEPA filter on site. Contact the Dyson Helpline on the number on the back cover of this manual for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following the instructions given in the
filter change kit. If in any doubt, consult a qualified electrician or contact the Dyson Helpline for support.
DISPOSAL INFORmATION
Dyson products are made from high grade recyclable materials. Please dispose of this product responsibly and recycle
where possible.
PLEASE REGISTER AS A DYSON AIRBLADE TAP HAND DRYER OwNER
To help us ensure you receive prompt and efficient service, please register your unit at www.dysonairblade.com
This will register your guarantee, confirm ownership of your Dyson unit in the event of an insurance loss, and enable us
to contact you if necessary.
You will need your serial number, which can be found on the bottom right hand corner of the backplate, on a
registration sheet in the box, and also on the large information sticker which can be found around the tap when it is
unpacked.
Please ensure all instructions and guidance in this operating manual, the installation guide and cleaning guide are
adhered to or your guarantee may be invalidated.
YOUR GUARANTEE
TERmS AND CONDITIONS OF THE DYSON 5 YEAR GUARANTEE.
16