Tabla De Contenido - Mitsubishi FX2N SERIE Manual Del Usaurio

FX2N Series Programmable Controllers FX2N Series Programmable Controllers
Table of Contents
ENG
Guidelines of Safety................................. ii
1. Introduction ......................................1-1
1.1 Unit Accessories.................................... 1-9
1.2 World Specification................................ 1-9
1.3 Model name......................................... 1-10
1.4 Serial number ...................................... 1-11
1.4.1 Product during December, 2009 or
earlier .............................................. 1-11
1.4.2 Product from January, 2010 ............ 1-12
1.5 Configuration ....................................... 1-13
1.5.1 Rules ............................................... 1-16
2. Terminal layouts...............................2-1
2.1 Relay out, 24V DC input MPU's - Main
Processing Unit (base units).................. 2-2
2.2 Transistor output, MPU's - (base units).. 2-3
2.3 Powered extension units ....................... 2-4
2.4 Extension blocks.................................... 2-4
2.5 FX Extension blocks .......................... 2-5
0N
2.6 AC 110V Input, MPUs - (base units) ..... 2-6
3. Installation ........................................3-1
3.1 Product outline....................................... 3-2
3.2 RUN/STOP Control ............................... 3-4
3.3 General specifications ........................... 3-6
3.4 PLC mounting arrangements................. 3-8
3.5 DIN rail mounting................................. 3-14
3.6 Direct mounting ................................... 3-15
3.7 General notes ...................................... 3-16
3.8 Extension Board Installation ................ 3-17
3.9 Extension Units/Blocks Installation...... 3-19
4. Wiring techniques.............................4-1
4.1 Wiring cautions ...................................... 4-1
4.2 Termination at screw terminals.............. 4-4
4.2.1 Removal and installation of quick-
release terminal block ....................... 4-7
4.3 Power supply ......................................... 4-9
4.4 Earthing/Grounding ............................. 4-15
4.5 Service power supply .......................... 4-16
5. Inputs ...............................................5-1
5.1 24V DC input specifications................... 5-1
5.1.1 Typical wiring..................................... 5-2
5.1.2 Input circuit connection...................... 5-3
5.1.3 Diodes and inputs connected in
series................................................. 5-4
5.1.4 Resistors and inputs connected in
parallel............................................... 5-5
Registration
®
• Microsoft and Windows
United States and/or other countries.
• The company name and the product name to be described in this manual are the registered trademarks or
trademarks of each company.
®
are either registered trademarks or trademarks of Microsoft Corporation in the
5.2 AC 110V Input, MPUs............................ 5-6
5.2.1 110V AC input specifications ............. 5-7
5.2.2 Typical wiring .....................................5-8
5.2.3 Programming caution......................... 5-9
6. Outputs ............................................ 6-1
6.1 Relay output specification...................... 6-1
6.1.1 Product life of relay contacts.............. 6-3
6.1.2 Relay output example ........................6-8
6.1.3 Output circuit configuration ................ 6-9
6.2 Triac (SSR) output specifications ........ 6-12
6.2.1 In-rush currents................................6-14
6.2.2 Triac output example ....................... 6-15
6.2.3 Output circuit configuration .............. 6-16
6.3 Transistor output specification ............. 6-18
6.3.1 Response times ............................... 6-20
6.3.2 Transistor output example ............... 6-21
6.4 Applying safe loads.............................. 6-22
7. Diagnostics ...................................... 7-1
7.1 Preliminary checks................................. 7-1
7.2 Basic diagnostics ................................... 7-2
7.2.1 Power ON, PLC OFF ......................... 7-2
7.2.2 BATT.V LED ON................................ 7-4
7.2.3 PROG.E LED flashes ........................7-6
7.2.4 CPU.E LED ON ................................. 7-7
7.3 Common errors.................................... 7-10
7.4 Writing of program and program check
[power ON and PLC stopped].............. 7-11
7.5 Replacing the battery........................... 7-16
7.6 Maintenance ........................................ 7-18
7.7 Error flags ON indicates error. ............. 7-19
7.8 Error registers ...................................... 7-21
7.9 Error codes .......................................... 7-23
7.10 Instruction list....................................... 7-24
Appendix A:Associated Manuals.......... A-1
Appendix B:Discontinued models ........ B-1
Appendix C:Precautions for Battery
Transportation ..................C-1
C-1: Regulated FX series products............C-1
2N
C-2: Transport guidelines ..............................C-1
Appendix D:Handling of Batteries and
Devices with Built-in Batteries
in EU Member States .......D-1
D-1: Disposal precautions .............................D-1
D-2: Exportation precautions .........................D-1
D-3: Regulated FX series products............D-1
2N
Appendix E:Index ................................. E-1
xiv