Initial Startup - REMS Picus S1 Manual De Instrucciones

eng
REMS UDKB 52 x 420 x UNC 1
REMS UDKB 62 x 420 x UNC 1
REMS UDKB 72 x 420 x UNC 1
REMS UDKB 82 x 420 x UNC 1
REMS UDKB 92 x 420 x UNC 1
REMS UDKB 102 x 420 x UNC 1
REMS UDKB 112 x 420 x UNC 1
REMS UDKB 125 x 420 x UNC 1
REMS UDKB 132 x 420 x UNC 1
REMS UDKB 152 x 420 x UNC 1
REMS UDKB 162 x 420 x UNC 1
REMS UDKB 182 x 420 x UNC 1
REMS UDKB 200 x 420 x UNC 1
REMS UDKB 225 x 420 x UNC 1
REMS UDKB 250 x 420 x UNC 1
REMS UDKB 300 x 420 x UNC 1
Expansion anchor M12 (masonry), 10 units
Knock-in anchor M12 (concrete), 50 units
Flattener for knock-in anchor M12
Fast-tightening nut set (art. no. 079007, 079008, 079009)
Knurled threaded rod M12 x 65
Fast-tightening nut
Washer
Tapping tool G 1 / for Ø 8 mm drill
2
Single-ended wrench SW 19
Single-ended wrench SW 30
Single-ended wrench SW 32
Single-ended wrench SW 41
Hexagon socket head wrench SW 3
Hexagon socket head wrench SW 6
Suction rotor for dust extraction
1
Adapter G / male – UNC 1
2
Adapter UNC 1¼ male – Hilti BI
Adapter UNC 1¼ male – Hilti BU
Adapter UNC 1¼ male – Würth
Annular core bit extension 200 mm x UNC 1
Sharpening stone
Pressurised water tank
Quick-release ring
Levelling block
Water suction device Simplex
Water suction device Duplex
1.2. Drilling depth
Useful drilling depth of the REMS Universal
diamond core drilling crown
Deeper core-drilling operations can be carried out with the annular
core bit extension (see 3.7).
1.3. Drilling range Picus S1
Core drilling operations
in steel-reinforced
concrete Ø 20–102
(132) mm
Core-drilling operations
in masonry Ø 20–152 mm Ø 20–252 mm Ø 40–300 mm
Annular-bit connection
thread UNC 1¼ male, UNC 1¼ male, UNC 1¼
G ½ female
Drill collar Ø 60 mm
1.4. Turning speed Picus S1
230 V, 50–60 Hz
1
Idling 830 min-
1
At rated load 580 min-
115 V, 50–60 Hz
Idling 940 min- 1
At rated load 740 min- 1
1.5. Electrical specifications
Supply voltage
Power consumption
Rated current capacity
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1 /
4
1
/
4
1
/
4
1
/
4
1 /
4
1 /
4
1 /
4
1 /
4
1
/ male
4
1 /
4
Picus S3 Picus S2/3,5
Ø 20–152 Ø 40–300 mm
(200) mm
G ½ female
60 mm
Picus S3 Picus S2/3,5
1
750, 1800, 2500 min- 490, 1160 min-
1
530, 1280, 1780 min- 320, 760 min-
770, 1860, 2580 min- 1 440, 1030 min-
570, 1380, 1920 min- 1 290, 680 min-
Picus S1 Picus S3 Picus S2/3,5
230 V, 50/60 Hz
1800 W 2200 W 3420 W
8.4 A 10 A 16 A
181020
181025 Fuse protection
181030 (mains network)
181035
Fault-current safety switch
181040
PRCD
181045
with low-voltage release
181050
Supply voltage
181057
Power consumption
181060
Rated current capacity
181065
Fuse protection
181070
(mains network)
181075
181080
Fault-current safety switch
181085
PRCD
181090
with low-voltage release
181095
1.6. Dimensions (L x W x H)
079006
REMS Picus S1 drive unit
079005
REMS Picus S3 drive unit
182050
REMS Picus S2/3,5 drive unit490 x 170 x 135 mm (19.3"×6.7"×5.3")
079010
REMS Simplex drill upright
079008
REMS Duplex drill upright
079009
REMS Duplex 300 drill upr. 480×300×1060 mm (18.9"×11.8"×41.7")
079007
180150
1.7. Weights
079000
REMS Picus S1 drive unit
079001
REMS Picus S3 drive unit
079002
REMS Picus S2/3,5 drive unit
079003
REMS Simplex drill upright
079011
REMS Duplex drill upright
079004
REMS Duplex 300 drill upright
180160
1.8. Noise emissions
180052
Workplace emission level
180053
Operating sound level
180054
180055
1.9. Vibrations
180155
Weighted effective value of
079012
acceleration
182006
180015

2. Initial startup

182009
182002
2.1. Electrical connection
182003
Before connecting the machine, check to ensure that the mains volta-
ge matches that indicated on the machine rating plate. Always check
the PRCD fault current-safety switch (19) for correct functioning before
starting up at the beginning of each session (see 3.).
420 mm
2.2. REMS Picus S1, REMS Picus S3 and REMS Picus S2/3,5
drive units
The REMS Picus S1, REMS Picus S3 and REMS Picus S2/3,5 drive
units are universally applicable for both dry and wet drilling, either ma-
nually controlled (Picus S1, Picus S3) or with drill upright. The combi-
ned drill crown connection of the drive spindle (11) of REMS Picus S1
and REMS Picus S3 allows both the direct mounting of diamond core
drill crowns with internal thread UNC 1¼ and with external thread G ½.
The Picus S1 and Picus S3 drive machines are not delivered with the
water feeding device (15) pre-assembled but loose. The adapter for the
water connection on the drive machines is closed by a cover (14). In this
condition the drive machines (REMS Picus S1, REMS Picus S3) are
used for dry drilling. The water feed device is already pre-assembled on
the REMS Picus S2/3,5. For wet drilling, see 2.5.
The drive-unit turning speed required for cost-effective core drilling de-
pends on the diameter of the diamond core drilling crown. Select the
turning speed of the drive unit in such a way that the peripheral speed
1
(cutting speed) of the diamond core drilling crown runs within a range
1
between 2 and 4 m/s. It is of course possible to carry out drilling opera-
tions outside this optimum range, albeit subject to reductions in the
1
operating speed and/or service life of the diamond core drilling crown.
1
Higher peripheral speed apply in masonry.
The turning speed of the REMS Picus S1 is adjusted to a fixed setting.
From a drilling diameter of 62 mm, the REMS Picus S1 operates in con-
crete in the optimum peripheral speed range, which always remains in-
side acceptable limits when smaller diameters are being handled. The
Picus S1 Picus S3 Picus S2/3,5
10 A (B) 16 A (B) 16 A (B)
10 mA 10 mA 10 mA
115 V, 50/60 Hz
1700 W 2050 W 2820 W
15 A 18 A 25 A
20 A 25 A 25 A
6 mA 6 mA 6 mA
460 x 160 x 100 mm (18.1"×6.3"×3.9")
540 x 160 x 100 mm (21.3"×6.3"×3.9")
400 x 200 x 775 mm (15.7"×7.9"×30.5")
440 x 230 x 935 mm (17.3"×9.1"×36.8")
5.2 kg (11.5 lb)
7.4 kg (16.3 lb)
13.6 kg (30.0 lb)
9.7 kg (21.4 lb)
12.8 kg (28.2 lb)
16.2 kg (35.8 lb)
Picus S1 Picus S3 Picus S2/3,5
90 dB (A) 90 dB (A) 91 dB (A)
103 dB (A) 103 dB (A) 104 dB (A)
2.5 m/s 2 2.5 m/s 2 2.5 m/s
eng
2