Connections Control Unit; How To Use The Carrera Race App/Carrera Appconnect; Connecting The Receiver; Connecting The Charging Unit - Carrera MIX ’N RACE VOLUME 3 Instrucciones De Uso

Connections Control Unit

1 2 3 4
Connections (from left to right):
Connection for Lap Counter 20030342
1
Connection for Carrera AppConnect 20030369, PC-Unit or
2
Lap Counter 20030355
Connector 1 for speed controller, speed controller extension set
3
or WIRELESS+ receiver
Connector 2 for WIRELESS Tower 20010108
4
5 Connector 3 for speed controller
Connector 4 for speed controller
6
Connection for DIGITAL 124 / DIGITAL 132 power supply
7
General information on connectors 1-4:
When a WIRELESS+ receiver is used, it must be plugged into con-
nector 1. Optionally a WIRELESS Tower 20010108 can be plugged
into connector 2. When only the WIRELESS+ receiver is used, con-
nector 2 is to be left empty.
How to use the Carrera Race
App/Carrera AppConnect
1
2 3
4
Symbolabbildung
Symbols
5
1
Upload the Carrera Race App onto your mobile terminal unit.
2
Connect the Bluetooth adapter to the socket PC unit according
to the symbol illustration.
3 Make sure that the Bluetooth function on your terminal unit is
activated. The Carrera AppConnect will continue to flash until a
connection is established.
4
Start the Carrera Race App.
A steady light from the blue diode shows that the Bluetooth con-
5
nection is established.
5 6 7
Additional wired speed controllers may be plugged into connectors
3 and 4. Please note that these will use address 5 and 6 then.
Using the speed controller extension set 20030348 it has to be
plugged into connector 1. The cars´ addresses will be allocated as
follows:
• Speed controller extension set = address 1, 3 and 4
• connector 2 = address 2
• connector 3 = address 5
• connector 4 = address 6
Note:
a combination of WIRELESS and speed controller extension set is
not possible!
Please note that in DIGITAL 124 the number of cars is restricted
to four.

Connecting the receiver

Connect the receiver according to the symbol to either of the two
sockets on the control unit which are marked Tower 1 and Tower 2.
For operating four WIRELESS+ speed controllers only one 2.4 GHz
receiver is required.

Connecting the charging unit

The charging unit is connected at the rear of the control unit. To site
the charging unit at any other place on the track, an adapter unit
20030360 will be needed.
Rear view of the
control unit

Charging the speed controllers

Before first being used, the WIRELESS+ speed controllers should
be fully charged. Place the speed controllers in the charging station
and switch on the control unit. While the unit is charging, the LEDs
on the speed controllers will flash. When charging is completed,
1
the LEDs will light up continuously.
1
When using a lithium polymer rechargeable battery, it is possible to
top up the speed controller at any time.

Binding process

1
1
CHANNEL
SET
3
1
3
CHANNEL
2
SET
Before the speed controller can be used to control the cars, it must
be "bound" to the receiver.
To do this, switch on the control unit.
1
The receiver indicates it is ready for operation by a revolving light
signal in the segment display
2
Push the "SET" button once until the figure 1 appears in the seg-
2
Symbols
ment display . The number shown is then the address of the car.
1
Switch to the next address by further pressing the button.
Now press the binding button
The speed controller signals a successful binding process with
flashing of the LED, while the receiver indicates it by revolving lights
in the segments. The binding process is now complete and the
speed controller is ready for use.
3
To bind the second speed controller, follow the same procedure.
Press the "SET" button
2
2 appears . Then press the binding button
1
speed controller.
4
To display the address set for the speed controller, press once on
the binding button on the top of the speed controller.
2
The LED will then flash, according to the address set.
1
If the speed controller is not actuated, it switches automatically after
about 20 seconds into energy-saving mode. The speed controller
can be reactivated by pressing the tappet or the lane-change button.
1 1
2
1
3
CHANNEL
2
SET
4
2
1
.
1
on the top of the speed controller.
3
on the receiver twice, until the figure
on the second
3
13