Overview Of Connections; Hdmi Inputs And Outputs; Rear Hdmi In 1-7 Video Inputs R; Front Hdmi In - Rotel RAP-1580MKII Manual De Instrucciones

Place the unit close to the other components in your system and, if possible,
on its own shelf or with the optionally included rack ears. This will make
initial connection, and subsequent system changes easier.
The unit can generate heat during normal operation. Do not block ventilation
openings. Allow a minimum of 10 cm or 4 inches of unobstructed space
around the unit. If installed in a cabinet, make sure that there is adequate
ventilation.
Do not stack other components or objects on top of the unit. Do not let any
liquid fall into the cabinet.

Overview of Connections

NOTE: Do NOT plug any system component into an AC source until
all connections have been properly made.
Each of the source components in the system are connected to the unit's
inputs with a pair of standard RCA cables for analog audio, an HDMI video
connection and an optional digital audio cable (coax or optical).
The outputs of the RAP-1580MKII can be sent up to 7 sets of speakers
or sent to power amplifier(s) with standard RCA cables from the preamp
audio outputs. Overhead channel outputs are also available via the RCA
pre-outputs for connection to an external amplifier delivering up to 7.1.4
channels of audio. The video signal from the RAP-1580MKII is sent to the
monitor using the HDMI connections.
In addition, the processor has MULTI INPUT connections for use with a
source component that does its own surround decoding, remote IR receiver
inputs and 12V trigger outputs.
NOTE: The S/PDIF digital audio interface standard specifies a 75
ohm impedance and all good digital cables adhere to this requirement.
Do NOT substitute conventional audio interconnect cables for digital
signals. Standard audio interconnects will pass these signals, but their
limited bandwidth reduce performance.
When using analog audio connections ensure the Left and Right signals are
attached to the proper RCA jacks. All RCA-type connections on this product
follow these standard color codes:
Left channel audio: white RCA jack
Right channel audio: red RCA jack
NOTE: Each source input must be properly configured using the INPUT
SETUP menu of the OSD menu system. We recommend going to this
menu after connecting all of the sources to configure it as desired. See
Input Setup in the Setup section for more information.

HDMI Inputs and Outputs

These connections are used for connecting video signals to and from the
unit. See the Making Connections section for specific instructions for each
type of component on page 17.
Rear HDMI IN 1–7 Video Inputs
HDMI inputs provide various digital video connections for use with components
that have HDMI outputs. HDMI connections carry video signals in multiple
formats including 3D, 1080p/24Hz, and 4K. The implementation of HDMI
supports audio signals, or a separate audio connection from an HDMI
component. Three HDMI inputs support 4K UHD HDCP 2.2 as labeled on
the rear panel.

Front HDMI IN

9
The Video 8 input is located on the front panel for easier access. Use
this HDMI connection for portable sources or devices that would not be
permanently connected.
HDMI Monitor Outputs
e
The two HDMI outputs of the RAP-1580MKII send High Definition video
signals to your TV monitor in parallel. The HDMI outputs can send video
signals to a high-definition TV 2D (480p/576p, 720p, 1080i, 1080p or
4K) and 3D (up to 1080p/24Hz). One HDMI output will support 4K UHD
HDCP 2.2 as labeled on the rear panel.
There are two HDMI outputs on the rear panel sending out the same video
signal. The ARC/OSD output will send the On Screen Menu to your TV.
Of the two HDMI Outputs, only one HDMI output supports ARC (Audio
Return Channel) and is labeled "ARC/OSD" above the HDMI connector.
Please refer to the VIDEO SETUP menu section of this manual for more
details on page 27.
Your TV may have more than one HDMI input. Not all HDMI inputs support
ARC. Please use the ARC enabled HDMI input of your TV to use the ARC
function on this product. ARC compatible inputs should be labeled with
"ARC" next to the HDMI input connector.
Additional information for HDMI video outputs:
• All HDMI attached devices must be HDCP compatible to ensure proper
display of the HDMI video signal.
• Audio received over HDMI will be processed by this product and sent
out via the RCA and speaker terminal outputs.
• When using both HDMI outputs simultaneously, both HDMI outputs
will be set to the same resolution. This resolution will be the lower
resolution of any attached monitor.

Audio Inputs and Outputs

This Rotel processor provides both analog and digital audio connections.
PHONO Input
g
A Left/Right pair of RCA analog audio inputs for connecting a phono player
with a moving magnet cartridge. If the turntable has a "ground" wire,
connect it to the screw terminal labeled "GND" to the left of the Digital inputs.
TUNER Input
g
A Left/Right pair of RCA analog audio inputs for connecting a tuner.
CD Input
g
A Left/Right pair of RCA analog audio inputs for connecting a CD player.
r
15