Installation; Connection To Water Supply; Electric Connection; Important - La Pavoni Bar T Instrucciones De Funcionamiento

5 – INSTALLATION
A. Water system.
B. Drain waste tube.
C. Protection switch.
D. Softener.
E. Drip tray.
F. Power supply cable.
THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH
THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING
CODES.
Before starting the installation, make sure that:
1. no dents, bumps or buckling exist;
2. no wet areas or other signs exist that may lead to the conclu-
sion that the packaging has been exposed to bad weather
conditions;
3. no tampering signs exist.
Once you have ensured that the transportation has been carried
out correctly, proceed with the installation.
Check that the machine is installed on a flat surface to a
minimum height of 90 cm fitted to support the weight, leav-
ing a clear area of at least 30 cm around the coffee machine.
Then proceed with the installation operations, following the next steps.
5.1 – CONNECTION TO WATER SUPPLY
Caution! The machine must be supplied with water
having a 8°F hardness.
It is advisable to install a water softener for the machine water system.
Caution! It is not possible to use pipes and gaskets
already used.
Make sure to connect the machine to drinkable water supply.
The connection to the water supply of the machine must be in
accordance with the country of destination.
The pressure of water entering the machine must not exceed 0,65Mpa
- Connect the softener (D) to the water system (A).
N.B. Before connecting the softener to the machine, carry out a
washing cycle until the water is absolutely clear, after that you may
connect the softener to the machine.
- Connect the drip tray (E) to the drain waste tube (B):
- Concerning the main pressure, if this exceeds 0,5Mpa (5bar),
it is advisable to install a balanced pressure reducer for high
pressure (a device whereby any supply increase does not affect
the output pressure).
CONNECTION TO WATER SUPPLY FOR THE PUB E MODEL
For the PUB E model, which is provided with a built-in water tank
(18), fill the basin with 2.5 litres of water. The machine is not
provided with a drain connection for waste water, which collects
in the lower drip tray (7); after delivering 20/25 cups of coffee,
remove the tray and empty it.
For the model provided with a connection to the water supply,
carry out the connection to the supply and make sure that the
machine is supplied with water; connect the hose (which is provi-
ded with the machine) with the elbow placed under the machine
and allow the waste water to flow into a drain or into a special
container provided.
5.2 – ELECTRIC CONNECTION
Caution! Before proceeding with electric connection,
make sure that voltage meets the specifications shown
in the CE plate.
Make sure that the electrical supply can bear the machine charge
(see chapter 4 - Technical Specifications Table).
Provided with a ground connection follow the regulations in use.
In this case make sure that the main cable is efficient, and that it
follows the national and European safety rules.
The user has to arrange for the machine power supply and protect
the line following a safety switch (cut-out box) following the regula-
tions used in the country in object.
Connect the power supply cable (F) to the electric socket with a
multipolar switch (C) will have to be arranged for network separa-
tion, with a distance between contacts of at least 3 mm.
The yellow/green
COMPULSORILY connected to the main ground system.
The machine is equipped with a terminal block under the drain pan
supported by the following symbol
The terminal block is capable of connecting power cables from
2,5mm to 6mm, with ring terminals for screw M6.

IMPORTANT

The single phase connection of espresso
coffee machine in granted only in a place
having an electric system with an impedan-
ce conformed to the assorbed current of the
> 100A
appliance.
27
18
coloured cable should
.
English
be