Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
− Clamping again the chain
− Chain change
− Leaving of machine (also for short-term interruption)
S
a
f
e
t
y
i
n
s
t
r
u
c
t
i
o
n
s
S
a
f
e
t
y
i
n
s
t
r
u
c
t
i
o
n
s
Fuels and fuel vapours are inflammable and may
cause serious injury on the skin or when inhaled.
Therefore be careful and provide sufficient
ventilation when handling with fuels.
• Do not smoke and avoid open flames when fuelling.
• Wear gloves when fuelling.
• Do not fuel in closed rooms.
• Stop the chain saw and allow it to cool down.
• Carefully open the tank cap to allow possible overpressure
to relax.
• Avoid spilling of fuel or oil. Clean the device immediately
when you have spilled fuel or oil. Change your clothes
immediately when you have spilled fuel or oil on them.
Make sure that no fuel can come into the soil.
• Carefully close the tank cap after fuelling and check that it
does not get loose during operation.
• Check that there is no leakage on the tank cap and fuel
lines. If there are leaks this product may not be started.
• Never use a device with damaged ignition cable and spark
plug connector.
• Only transport and store fuels in containers approved and
identified for this.
• Keep children away from fuels.
• Do not handle and store fuels close to combustible and
highly inflammable materials as well as sparks and open
flames.
• Go away at least three metres from the fuelling place to
start the chain saw.
D
e
s
c
r
i
p
D
e
s
c
r
i
p
Pos.
Denomination
1
Drive unit
2
Clamping screw
3
Handle, cpl.
4
Handle
5
Lower handle
6
Rubber sleeve
7
Carrying strap
8
Throttle lever lock
9
Throttle trigger
10
ON/OFF switch
11
Priming pump
12
Choke lever
13
Cranking handle
14
Air filter cover
15
Air filter
16
Spark plug connector
17
Spark plug
18
Silencer
-
S
a
f
e
h
a
n
d
l
i
n
g
w
i
t
h
-
S
a
f
e
h
a
n
d
l
i
n
g
w
i
t
h
t
i
o
n
o
f
d
e
v
i
c
e
t
i
o
n
o
f
d
e
v
i
c
e
Order number
386126
386105
386104
386148
386150
386149
380856
386155
19
Tank cap
20
Fuel filter
21
Tank
22
Installation wrench
23
Allen key, size 4
f
u
e
l
s
f
u
e
l
s
24
Allen key, size 5
25
Open-end wrench, size 8/10
26
Round file
27
Fuel mixing can
28
Brushcutter attachment tool
29
Safety label
30
Safety guard
31
Safety guard holder
32
Holder
33
Protective cover
34
Angular gear
35
Hexagon nut
36
Cover
37
Spacer washer
38
Cutting blade
39
Thread spool
40
Thread spool holder
41
Thread spool cover
42
Spring
43
Thread knife
44
Hedge trimmer attachment tool
45
Cutting device
46
Cutting tool guard
47
Handle
48
Safety label
49
Pruner attachment tool
50
Guide bar (sword)
51
Safety label
52
Saw chain
53
Chain protection
54
Cover
55
Fixing nut
56
Chain wheel
57
Chain stretching screw
58
Chain stretching pin
59
Oil tank lock
60
Protective cap
61
Zerk fitting
62
Accessories bag
Installation tools
Please note the attached assembly instruction
sheet!
Remove the protective cap (60) and slide the
brushcutter (28), hedge trimmer (44) or pruner (49)
attachement tool in the holder (a) of the drive unit (1) as
shown.
Make sure that it engages with a click.
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
y
A
s
s
e
m
b
l
i
n
g
/
d
i
s
a
s
s
e
m
b
A
s
s
e
m
b
l
i
n
g
/
d
i
s
a
s
s
e
m
b
386153
386152
386103
386182
364520
386156
386102
386121
386120
386119
386118
386129
386131
386132
386133
386122
386114
386115
386116
386157
386159
386158
386151
386163
386164
386160
386184
386174
386183
l
i
n
g
l
i
n
g
29
Publicidad
Capítulos
Tabla de contenido
