Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
C
h
e
c
k
i
n
g
t
h
C
h
e
c
k
i
n
g
t
h
Never operate the power pruner without functioning
chain lubrication.
Check the function of the automatic chain lubrication by
switching on the power pruner and holding it with the spike in
direction of a carton or paper on the ground.
Do not get in contact with the ground with the chain. Keep
a safe distance of 20 cm.
If an increasing oil track is caused when checking it the oil
automatic works faultless.
If there is no oil track despite full oil tank
clean the oil flow canal (h) and clean the upper chain
clamping boring (g)
adjust the chain lubrication as described under
"
Adjusting the chain lubrication".
If this is not successful please contact the customer service.
You may not start to operate the machine until you
have read these operating instructions, observed all the
instructions
given
and
assembled the machine!
Before each use, check
- the machine for possible damage:
- loose fastenings
Make sure that the ON/OFF switch, the throttle lock-out
switch, the throttle trigger and the machine properly work.
The engine of the machine is supplied without
gasoline and oil in it. Fuel the device as described under
"Fuelling".
S
t
a
r
t
i
n
g
S
t
a
r
t
i
n
This machine is equipped with a centrifugal clutch.
The cutting tool can start rotating after the start. Place the
machine therefore on a solid ground for starting. Firmly
hold the machine and make sure that neither the cutting
tool nor the throttle lever come into contact with fixed
objects.
Always keep your hands and feet at a safe distance to the
cutting tool.
Put the machine on the ground.
Have a safe standing position.
Make sure that the cutting tool has no contact with the
ground.
S
t
a
r
t
i
n
g
w
S
t
a
r
t
i
n
g
w
Firmly press on the fuel pump (11) several times until
petrol (gasoline)/foam is visible in the priming pump.
32
e
c
h
a
i
n
l
u
b
r
i
c
a
t
i
o
n
e
c
h
a
i
n
l
u
b
r
i
c
a
t
i
o
n
S
t
a
r
t
-
u
p
S
t
a
r
t
-
u
p
completely
and
properly
t
h
e
m
a
c
h
i
n
e
g
t
h
e
m
a
c
h
i
n
e
i
t
h
c
o
l
d
e
n
g
i
n
e
i
t
h
c
o
l
d
e
n
g
i
n
e
Put the choke lever (12) to the position
Put the ON/OFF switch (10) to
Press the throttle lock-out switch (8) and operate the
throttle trigger (9) at the same time.
Grasp the cranking handle (13) and slowly pull the
cranking rope until a resistance is felt. Then, pull quickly
and firmly.
Do not fully pull out the cranking rope and slowly
guide the cranking handle back to make sure that
the cranking rope is correctly wound up.
Repeat this operation until the engine starts.
Put the choke lever (12) to the position
engine has started.
The engine will idle when you release the throttle
trigger.
The cutting tool may not move in idle mode. Risk of injury!
Immediately stop the operation when the cutting
device moves while the throttle is disengaged. The
idle speed must be reduced. (See "Maintenance
adjusting the carburetor")
S
S
t
t
o
o
p
p
p
p
i
i
Release the throttle trigger (9).
Put the ON/OFF switch (10) to the position
S
t
a
r
t
i
n
g
w
S
t
a
r
t
i
n
g
w
Start the device as described under "Starting with cold engine",
but leave the choke lever in its operating position
not operate the throttle trigger.
W
o
r
k
W
o
r
k
You may not start to operate the machine until you
have read these operating instructions, observed all the
instructions given and installed the machine as described!
Always apply the carrying strap (7) when working
with this machine.
Adjust the carrying strap so that a convenient and safe carrying
of the machine is ensured.
The quick acting closure (A) is located at the front.
The quick acting closure can be opened with the left
hand.
The hip pad (B) should rest on the hip.
Immediately replace a damaged carrying strap.
Always keep your hands and feet at a safe distance
to the cutting tool.
.
.
when the
n
n
g
g
t
t
h
h
e
e
e
e
n
n
g
g
i
i
n
n
e
e
i
t
h
w
a
r
m
e
n
g
i
n
e
i
t
h
w
a
r
m
e
n
g
i
n
e
i
n
g
i
n
s
t
r
u
c
t
i
o
n
s
i
n
g
i
n
s
t
r
u
c
t
i
o
n
s
.
and do
Publicidad
Capítulos
Tabla de contenido
