SRAM RockShox Pike Manual De Usuario página 6

English
reboUnd daMping
external rebound adjustment
Rebound damping controls the speed at which a fork returns to its full extension following compression.
Located at the bottom of the right fork leg is the rebound adjuster knob. Turning the adjuster in the direction
indicated by the "rabbit" on the rebound speed decal decreases rebound damping, causing the fork
to return to full extension faster. Turning the adjuster in the direction indicated by the "turtle" increases
rebound damping, slowing the return of the fork to full extension.
Excessive rebound damping will cause the fork to "pack up" over successive bumps, reducing travel and
causing the fork to bottom out. Set your fork to rebound as fast as possible without "topping out" or kicking
back. This allows your fork to follow the contours of the trail, maximizing stability, traction and control.
Motion Control daMping systeM
(pike, revelation, reba, domain 318is, argyle 318 & 409)
important: When storing a bicycle or fork upside-down or on its side, oil sealed in the upper tube can
collect above the Motion Control Damper assembly. Upon returning the bicycle/fork to a normal riding
position, initial performance of the Motion Control system may be less than optimal. To quickly return the
fork to proper performance, return the fork to 'Open' position and cycle the fork through its travel 0-20
times. For information on returning your fork to 'Open' position, keep reading!
The Motion Control Damping system allows riders to quickly adjust the feel and performance of their
suspension to match riding conditions without requiring pumps or tools. This system provides for
wide-ranging control of compression and rebound damping as well as 'Lock' threshold sensitivity.
Proper setup of the Motion Control Damping system provides a range of options for efficient yet comfortable
performance. The instructions below describe setup and operation for both crown and remote activated forks.
'open' compression (fig. 1)
In the 'Open' position, the Motion Control Damping system allows for maximum compliance and fork
movement. The 'Open' position provides ultimate control and comfort on even the roughest terrain.
To return your fork to the 'Open' position:
• For forks with the crown-mounted blue compression adjuster, rotate the adjuster fully counterclockwise.
• For PopLoc equipped forks, press the "unlock" release button on the remote (as indicated by the open
padlock icon on the button).
8
Pike, Reba, Revelation, Domain & Argyle User Manual
fig. 1
95-405-000-000, Rev. A
Pike, Reba, Revelation, Domain & Argyle User Manual
'lock' compression (fig. 2)
In the 'Lock' position, the Motion Control system allows for a small amount of controlled fork movement.
This movement enables the front tire to track the terrain without deflecting off obstacles, allowing for better
traction and steering control when compared to a complete lockout system. To activate the 'Lock', turn the
crown-mounted blue compression adjuster full clockwise or press forward on the PopLoc Remote lever
located on the handlebar.
floodgate adjustment (fig. 3) (argyle 409, pike, revelation and reba only)
All forks with Motion Control Damping allow for fine-tuning of the 'Lock' setting. The rider can choose the
point at which the 'Lock' setting can 'blow-off' and become active to force inputs such as bumps or rocks.
This adjustment is made using the Floodgate. Depending upon fork model, the Floodgate is adjusted either
internally (requires a 2.5mm hex wrench) or externally with the gold 'Gate' adjuster.
For crown mounted adjusters, hold the adjuster in the 'Lock' position while adjusting the internal Floodgate.
note: The Floodgate is intended to adjust threshold of 'lock' blow-off in the 'lock' mode only. When
performing Floodgate adjustments, ensure that the motion control system is adjusted to 'lock.'
Under 'Lock', the maximum Floodgate setting results in a fork with minimal movement while the minimum
Floodgate setting results in increased fork movement.
note: For maximum fork sensitivity and movement, return the fork to the 'open' position.
Floodgate settings should be used to adjust suspension compliance to medium sized bumps and
resistance to rider induced suspension movement (referred to as "bob") in the 'Lock' mode. When properly
tuned, the Motion Control System will resist "bob," but provide controlled suspension action in rough or
aggressive terrain.
© SRAM Corporation • May 2006
fig. 2
English
9