FAS International JUST NOW Manual Del Usuario página 68

24
Command 69 Chooses functioning mode of the coin mechanism:
This command chooses the type and mode of functioning of the coin mechanism. The parameter can
assume the following values:
0 System EXECUTIVE with prices controlled in the machine (see relevant paragraph).
1 System EXECUTIVE in PRICE HOLDING mode (i.e. prices programmed in the coin mechanism). In this
case, the prices programmed at command 03 and those programmed in the coin mechanism must be the
same (see relevant paragraph). Alternatively you can set the "Price-Display" parameter. If enabled, the
vending machine will utilize exclusively the information on the price value deriving from the payment system,
that is, it will not be necessary to fill in the price tables (Commands 03 and 04); simply set only Command 05
(see relevant paragraph).
4 System BDV 001 (see paragraph using the coin mechanism BDV)
5 Payment system MDB (see paragraph on using the MDB payment system).
Command 70 Buzzer operation option:
By setting this command at zero the buzzer is disconnected during machine operation.
E
Command 72 Enabling the microwave oven:
N
This command enables operation of the microwave oven. Value 1 = oven enabled, 0 = oven not enabled. If
G
the command is set at 1, the heating time in seconds can be set for every selection. Default = 0 (no heating)
L
and it can be set between 0 and 120 sec.
I
S
Alternatively the heating times can be programmed by food zone (drawer): selection 91 means that all the
H
selections in the first food zone at the top have the same heating times. Selection 92 = 2
food zone; 94 = 4
will have the same setting.
Press Key 1 from the external keyboard and confirm with "ENTER".
Status of the main inputs: The display shows the status of the main inputs of the oven control board.
CO
0
CO oven chamber cover opening input status: 1 = cover open.
CC oven chamber cover closure input status: 1 = cover closed.
FL status of the bottom photocells: 1 = photocells engaged.
FU status of the top photocells: 1 = photocells engaged.
DL product delivery position microswitch status: 1 = in position.
HT product heating position microswitch status: 1 = in position.
HM HOME (product loading) position microswitch status: 1 = in position.
Press Key 2 from the external keyboard and confirm with "ENTER".
"Product turnover rods" top and bottom / interference / test photocell operation.
a) When you break and then restore the light beam of the top and bottom photocell you will receive a
signal that they are working properly.
b) Oven interference test with the bottom photocells: when you press "ENTER" the oven chamber is
rotated to the product delivery position and a check is carried out to ensure that the oven chamber
interferes with the bottom photocells during its movement.
c) Test of the product entrapment prevention device (turnover rods): a complete cycle of the device is
carried out every time the "ENTER" key is pressed.
FAS INTERNATIONAL S.p.A. Via Lago di Vico, 60 SCHIO (VI) – tel. +39 0445 502011 – fax +39 0445 502010 - e-mail: info@fas.it
th
food zone. If 99 is selected for the heating time, all the selections in the vending machine
In order to set the following options you must press the "Test Button" twice
consecutively, as confirmed by the sound of the buzzer. You will access the second level
of the menu in this way. "Command 00" will appear on the display. Press the "ESC" key
several times to abandon programming mode.ATTENTION: the microwave oven
safety devices are deactivated for the available options that follow! These
operations must be carried out exclusively by EXPERT personnel.
CC FL
0 1
FU DL
0 0
JUST NOW – Issue 00
nd rd
food zone; 93 = 3
HT HM
0 0