Storage And Transportation - Cerva ALPINWORKER PRO UNVENTED Manual Del Usuario

GB
FOREWORD: Do not wear jewelry, rings, bracelets, ear-rings...during your work.
People with sensitive skin may fi nd that contact with certain materials causes an allergic reaction.
If this should occur please refer to your doctor and avoid the material concerned.
For reasons of safety and hygiene, this product is for personal use only.
Before use, you must imperatively read the manual and ensure that you have clearly understood how the product should be
used. Don't throw it away. Keep it for future use
CONFORMITY
This product complies with the European REGULATION (EU) 2016/425. This Protective Industrial Safety Helmet satisfi ed the
essential requirements of the standard; EN 397:2012 +A1:2012 – "Industrial Safety Helmet" and EN 50365:2002 Insulating
helmets for use on low voltage installations.
Certifi cation for these products had been issued by: BSI Group The Netherlands B.V., John M. Keynesplein 9,
1066 EP Amsterdam, The Netherlands. Notifi ed Body : 2797
FEATURES: The performance characteristics for which the helmet has been designed are guaranteed only if it is used correctly
and if maintenance is perform as described in the instructions. Should this not be the case, then the protective features cannot
be guaranteed.
WARNINGS: Failure to respect the warnings listed below could have grave, and even life-threateing, consequences. This
helmet is designed to provide protection from impact, from penetration from above, from tension and from exposure to fl ames,
within the limits contemplated under the EN 397:2012+A1:2012 Norm.
It is meant to reduce the eff ects of unforeseen events, but it cannot protect the head from all eventualities.
TO ENSURE MAXIMUM PROTECTION, THE HELMET:
• MUST be properly placed on the head, and the webbing must be adjusted to ensure that the helmet fi ts snugly, though with a
certain degree of comfort.
• To ensure maximum stability of the helmet, always attach and adjust the chinstrap correctly; this will help reduce shifting of the
helmet resulting from certain environmental conditions.
• Inspect the helmet before and after each use, employing the inspection procedures described in this manual and immediately
replacing any worn or damaged part exclusively with spare parts supplied by CERVA GROUP a.s. .
•NEVER use paints, solvents or detergents made from hydrocarbons on this helmet. Such substances can damage the mate-
rials in a manner not visible to the eye, reducing their protective actions.
MAINTENANCE CLEANING AND DISINFECTING
The helmet may be cleaned with the use of soap and warm water and dried with soft cloth. The helmet should not be cleaned
with abrasive substances or solvents.
Follow the procedure to clean the helmet
1) Dismantle the helmet.
2) Clean all the pieces inside and outside using only neutral soap and lukewarm water, with the exception of swetband.
Do not use solvents, let dry at room temperature.

STORAGE AND TRANSPORTATION

This helmet MUST be kept in a clean, dry spot, not near sources of heat and at constant temperature of between 20° ± 15°C.
• NEVER keep the helmet inside the vehicle when not being used. Not only will it be exposed to sunlight (UV rays and heat),
but, if not adequate set in place, it could also be thrown about inside the vehicle in the events of a sudden stop.
• This helmet should be stored in original packing container out of direct sunlight, away from chemical and abrasive substances
and where it will not be damaged by physical contact with hard surfaces/items.
Keep the product in its original package when transporting. Do not put any weight above it.
SHOCKS: After a strong shock this helmet not to be use anymore. Internal invisible breakings could cause resistance reducti-
ons in the following impacts.
CHEMICAL AGENTS: All chemical products, corrosive substances and solvents could, in certain concentrations, prove
dangerous for this product. If it is possible or necessary for your helmet to come into contact with such substances, do not use
it in these conditions.
MARKING EN 397:2012 +A1:2012
The marking of the helmet shall contain the relevant technical information presented as follows:
1) Helmet model;
2) Name or identifi cation mark of the manufacturer;
3) Optional test; tested at low temperature;
4) Optional test; tested for molten metal splash;
5) Marking CE;
6) CE Notifi ed Body number;
7) Optional test; tested for lateral deformation;
8) Standard references;
9) Optional test; tested for electrical insulation;
10) Size covered by webbing (in centimeter)