Operation And Maintenance - GRAPHITE 58G955 Instrucciones De Uso

• After the engine has been heated, release pressure on the throttle
lever (7) and allow the engine to run slowly.
• Turn idle speed adjustment screw (17) counter-clockwise until the
blades stop moving. When idle speed appears to be too low, turn
the screw clockwise (fig. I).
Avoid touching the muffler. Hot muffler may cause severe burns.
BLADE BRAKE
This hedge trimmer is equipped with automatic brake that stops the
blades as soon as the throttle lever (7) has been released. The brake
engages automatically when force of inertia is applied to the weight
located inside the brake casing.
Make sure the blade brake operates correctly before starting any
task. In case the brake does not operate efficiently, adjust it or
repair in authorized service site.
INSTRUCTIONS REGARDING SAFE USE
Before starting to work, carefully check the hedge against
invisible objects, such as fence, mesh etc.
• When trimming long branches perform the work gradually, by
layers.
• Operate the hedge trimmer only when the hedge is dry.
• After the work is finished put the blade bar shields on.
TRIMMING HEDGES
• Besides trimming hedges, the hedge trimmer can also be used to
trim bushes and shrubs.
• The best results can be achieved when guiding the blade bar so it
is at an angle of approx. 15° with respect to the hedge.
• Two sided blade bar and counter-moving cutting parts allow
cutting in both directions or with swinging motion (fig. J).
• To obtain uniform height of hedge, it is recommended to extend
a rope or a line along trimmed hedge plane. Cut branches
protruding above the defined line (fig. K).
• To guide the branches into the blade, move the blade bar evenly
forward or backward along the line of cutting.
• Trim hedge sides in circular motions, from bottom to top (fig. L).
OPERATING THE HEDGE TRIMMER
• Before starting any planned task, familiarize yourself with
section describing rules for safe hedge trimmer operation.
• Always observe safety regulations.
• The hedge trimmer can only be used to cut wood. Cutting
other materials is forbidden.
• Do not use the hedge trimmer as a lever to lift, move or split
objects.
• Do not fix the device to a stationary work station.
• It is not necessary to apply big force to the hedge trimmer
when cutting. Apply only light pressure while the engine is
operating with the throttle fully opened.
• Press the throttle lever lock (6) and the throttle lever (7) (wait until
engine reaches its full speed before starting to cut).
• Keep maximum speed all the time.
• When the cutting has been finished release the throttle lever (7)
and allow the engine to run idle.
• Switch off the engine before putting the hedge trimmer away.
Keeping high speed of the trimmer engine when not cutting
wood causes unnecessary losses and wear of parts.
Always use complete safety equipment and appropriate working
clothes when operating the hedge trimmer.
Disassembly of protections,
maintenance, incorrect part replacement may contribute to
increased risk of body injury. Never modify the hedge trimmer
in any way. By using hedge trimmer with unauthorised
modifications, the user looses all warranty rights. Warranty voids
also when the hedge trimmer is used contrary to information
contained in this manual.
inappropriate operation,
14
CUTTING BRANCHES OF BUSHES
Do not cut branches when climbing up the tree. Do not stand on
ladder, platforms, logs or positions that may cause loss of balance
and control over the hedge trimmer. Do not cut above level of
your shoulders. Always hold the hedge trimmer with both hands.

OPERATION AND MAINTENANCE

Make sure the engine is switched off and cold before cleaning,
checking or repairing the hedge trimmer. Disconnect wire from
the ignition plug to prevent accidental start up of the engine.
Exercise caution due to sharp edges of cutting blades. When not in
use, the blade bar shall always be protected with the blade shield.
CLEANING
• Clean hedge trimmer body and plastic parts with soft brush and
cloth.
• Do not use water or agents with solvents or polishing substances.
• Remember to always keep the ventilation holes of the hedge
trimmer casing clean.
MAINTENANCE
• Check the hedge trimmer against obvious damages, such as
loosened or damaged blade, loose screw joints and worn out or
damaged structural parts.
• Make sure that guards and protection parts are not damaged and
installed properly. Carry out all necessary maintenance and repair
works before using the hedge trimmer.
• Clean the blade bar and spray maintenance liquid on it after each
use. When operating the tool for a long time, it is recommended to
regularly lubricate the blade with thin layer of oil (fig. M).
• Check condition of blade edges.
• You can proceed only with the device maintenance actions, which
are described within this instruction manual. Any other action can
be carried out only by authorized service.
• Do not make any changes in the hedge trimmer design.
STORAGE
• Empty the fuel system before deciding to store the tool for more
than one month.
• Drain fuel from the fuel tank, start the engine and allow it to use all
remaining fuel and stop working.
• Use new fuel each season. Never use any cleaning agents on fuel
tank, it may damage the engine.
• Store the hedge trimmer in a safe, dry place, beyond reach of
children.
• Do not put any objects on the hedge trimmer body.
When storing, it is important to avoid deposition of rubber
particles in basic parts of the fuel system, such as carburettor, fuel
filter, fuel line and fuel tank. Fuels with alcohol additives (ethanol
or methanol) may absorb moisture, and that during storing causes
separation of fuel blend ingredients and formation of acids. Acidic
petrol may damage the engine.
AIR FILTER
Dirty air filter reduces efficiency of combustion engine and causes
increase of fuel consumption. Clean the air filter after each 5 hours
of the device operation.
• Clean the air filter lid (14) and its surroundings, so the dirt does
not get into the carburettor chamber after the lid is removed.
• Press in the air filter lid locking button and remove the air filter
lid (fig. N).
• Remove the air filter (19) and wash it in water with soap, flush with
clean water and dry (fig. O).
• Install air filter insert (19). Make sure the grooves on the air filter
rim match with the protrusions on the air filter casing (14).
• Install the air filter lid (14).
Do not wash the air filter in petrol or any other flammable solvent
to avoid risk of fire or appearance of dangerous vapours.