Technical Parameters; Environment Protection; Betriebsanleitung - GRAPHITE 58G955 Instrucciones De Uso

FUEL FILTER
• Unscrew the fuel filler plug (11).
• Use wire hook to remove the fuel filter (20) through the fuel filler
hole (fig. P).
• Disassemble the fuel filter and wash it in petrol or replace with
a new one.
• Install the fuel filter in the tank.
• Tighten the fuel filler plug (11).
When the filter has been removed, use the wire hook to hold up
the end of the suction line. Be careful during fuel filter installation
to prevent contamination from getting into the suction line. When
putting the fuel filter into the tank make sure it reaches the back
corner.
IGNITION PLUG
To maintain reliable operation of the device, check condition of the
ignition plug on a regular basis.
• Remove the park plug boot from the spark plug (15).
• Put on plug key (included) and unscrew the ignition plug (fig. R).
• Clean and adjust spacing between contacts (0.65 mm) (fig. S).
• Install the spark plug (or replace with a new one if necessary) in
reverse order to removal.
OTHER INSTRUCTIONS
Make sure there are no fuel leaks, loosened joints or damages of
main parts, especially main handle joints and blade bar fixing. When
you find any damage, make sure the hedge trimmer is repaired
before next use.
All defects should be repaired by service workshop authorized by
the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Petrol Hedge Trimmer 58G955
Parameter
Engine displacement
Engine power
Maximum speed of cutting system,
no load
Maximum engine speed, no load
Engine idle rotational speed
Fuel consumption
Fuel: fuel blend composition
Carburettor
Ignition system
Ignition plug
Fuel tank capacity
Cutting width
Maximum thickness of cut branch
Weight
Year of production
58G955 defines type and indication of the device
NOISE LEVEL AND VIBRATION PARAMETERS
Sound pressure
Sound power
Vibration acceleration (front
handle)
Value
26 ccm
0,75 kW (1,02 KM)
2000 rpm
8500 rpm
3000 rpm
0,76 l/h
Petrol / oil (for 2-stroke
engines) 25 : 1
membrane
CDI
L7RTC; BM6A; L7T
600 ml
550 mm
20 mm
6 kg
2018
Lp = 101,29 dB(A) K= 3 dB(A)
A
Lw = 106,68 dB(A) K= 3 dB(A)
A
2 2
a = 4,081 m/s K= 1,5 m/s
h
Vibration acceleration (rear
handle)
Noise and vibration information
Noise produced by the device is defined with: level of produced
sound pressure Lp and level of sound power Lw
A
measurement uncertainty). Vibrations produced by the device
are defined with vibration acceleration value a
measurement uncertainty).
Sound pressure Lp , sound power Lw
A
specified in this manual have been measured in accordance with EN
ISO 10517:2009. Specified vibration level a
tools and for initial evaluation of exposition to vibrations.
Specified vibration level is representative only for main applications
of the device. When the device is used for other purposes or with
different working tools, the vibration level may change. Insufficient
or too rare maintenance may increase vibration level. The
abovementioned factors may lead to higher exposure to vibrations
during whole working time.
In order to precisely define exposure to vibrations, include periods
when the device is switched off and when it is switched on but not
used for working. Once all factors have been carefully considered,
total exposition to vibrations may be significantly lower.
To protect the user from results of exposure to vibrations, use
additional safety measures such as: device and working tool periodic
maintenance, proper hand temperature conditions, good work
organisation.

ENVIRONMENT PROTECTION

Do not dispose of combustion engine driven products with household
wastes, they should be utilized in proper plants. Obtain information on
waste utilization from your seller or local authorities. Worn out equipment
contains substances active in natural environment. Unrecycled equipment
constitutes a potential risk for environment and human health.
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with seat in Warsaw at
ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs, that all copyrights to this instruction (hereinafter
Instruction), including, but not limited to, text, photographies, schemes, drawings and layout of the
instruction, belong to Grupa Topex exclusively and are protected by laws accordingly to Copyright
and Related Rights Act of 4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz. U.
2006 No 90 item 631 with later ammendments). Copying, processing, publishing, modifications for
commercial purposes of the entire Instruction or its parts without written permission of Grupa Topex
are strictly forbidden and may cause civil and legal liability.
ÜBERSETZUNG DER
ORIGINALBETRIEBSANLEITUNG
HECKENSCHERE MIT
VERBRENNUNGSMOTOR
ANMERKUNG: LESEN SIE DIE VORLIEGENDE BETRIEBSANLEITUNG
VOR DER INBETRIEBNAHME DIESES GERÄTES SORGFÄLTIG DURCH
UND BEWAHREN SIE DIESE FÜR SPÄTERES NACHSCHLAGEN AUF.
DETAILLIERTE SICHERHEITSVORSCHRIFTEN
LESEN SIE DIE BEDIENUNGSANLEITUNG, BEVOR SIE DAS
GERÄT IN BETRIEB NEHMEN.
Vorbereitung
a) DIE HECKENSCHERE
VERURSACHEN. Lesen Sie die Anleitung sorgfältig durch und
wissen Sie, wie Sie die Heckenscheren richtig handhaben,
vorbereiten, warten, in Betrieb nehmen und stoppen. Machen Sie
sich mit allen Bedienelementen und dem richtigen Gebrauch der
Heckenschere vertraut.
b) Kinder dürfen keine Heckenscheren benutzen.
c) Achten Sie auf Freileitungen.
d) Außerhalb der Reichweite von Personen, insbesondere Kindern,
während der Arbeit aufbewahren.
15
2
a = 4,358 m/s K= 1,5 m/s
h
(where K is
A
(where K is
h
and vibration acceleration a
A
can be used to compare
h
58G955
KANN SCHWERE VERLETZUNGEN
2
h