Maintenance; Routine Maintenance; Cleaning The Inside Of The Machine - Stel THOR 103 Manual De Instrucciones

TECHNICAL
DESCRIPTION
7.0– MAINTENANCE
7.1– ROUTINE MAINTENANCE
BEFORE INSPECTING OR CHANGING PARTS OF THE TORCH, SWITCH
OFF THE POWER SUPPLY TO THE THOR.
IN NO CASE MUST MAINTENANCE WORK BE DONE WITHOUT HAVING
FIRST DISCONNECTED THE POWER SOURCE.
THE GREATEST CARE MUST BE TAKEN WHEN CHECKING THE INSIDE OF
THE MACHINE, DUE TO THE PRESENCE OF DANGEROUS VOLTAGE.
IT IS OBLIGATORY TO REMOVE THE PLUG FROM THE POWER SOCKET
BEFORE CARRYING OUT ANY MAINTENANCE WORK ON THE MACHINE.
THE ELECTROLYTIC CONDENSERS INSTALLED INSIDE THE MACHINE
REMAIN LIVE EVEN AFTER THE PLUG HAS BEEN REMOVED FROM THE
POWER SOCKET. IT IS OBLIGATORY TO WAIT AT LEAST 5 MINUTES
BEFORE REMOVING THE CASING AND GAINING ACCESS TO THE
INSIDE.
The lasting efficiency of the machine is directly linked with the frequency
of maintenance operations.
It is sufficient to clean the inside of the machine, which must be done all
the more frequently the dustier the work environment.

7.2- CLEANING THE INSIDE OF THE MACHINE

Before cleaning the inside of the machine it is obligatory to follow the
warnings described above and to proceed as follows:
1- Remove the casing, slackening the side screws;
2- Remove all traces of dust from the internal parts of the machine by
means of a jet of compressed air at a pressure no higher than 3 Kg/cm
3- Visually check all the electrical connections, ensuring that the screws
and nuts are well secured;
4- Visually check the state of all the components: replace any
deteriorated components;
5- Put back the casing, tightening the side screws.
7.3- PREVENTIVE MAINTENANCE OF THE
50
ENGLISH
THOR 103
COD. 6909500060
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
TECHNICAL
DESCRIPTION
7.0– MAINTENANCE
7.1– ROUTINE MAINTENANCE
BEFORE INSPECTING OR CHANGING PARTS OF THE TORCH, SWITCH
OFF THE POWER SUPPLY TO THE THOR.
IN NO CASE MUST MAINTENANCE WORK BE DONE WITHOUT HAVING
FIRST DISCONNECTED THE POWER SOURCE.
THE GREATEST CARE MUST BE TAKEN WHEN CHECKING THE INSIDE OF
THE MACHINE, DUE TO THE PRESENCE OF DANGEROUS VOLTAGE.
IT IS OBLIGATORY TO REMOVE THE PLUG FROM THE POWER SOCKET
BEFORE CARRYING OUT ANY MAINTENANCE WORK ON THE MACHINE.
THE ELECTROLYTIC CONDENSERS INSTALLED INSIDE THE MACHINE
REMAIN LIVE EVEN AFTER THE PLUG HAS BEEN REMOVED FROM THE
POWER SOCKET. IT IS OBLIGATORY TO WAIT AT LEAST 5 MINUTES
BEFORE REMOVING THE CASING AND GAINING ACCESS TO THE
INSIDE.
The lasting efficiency of the machine is directly linked with the frequency
of maintenance operations.
It is sufficient to clean the inside of the machine, which must be done all
the more frequently the dustier the work environment.
7.2- CLEANING THE INSIDE OF THE MACHINE
Before cleaning the inside of the machine it is obligatory to follow the
warnings described above and to proceed as follows:
1- Remove the casing, slackening the side screws;
2- Remove all traces of dust from the internal parts of the machine by
2
; means of a jet of compressed air at a pressure no higher than 3 Kg/cm
3- Visually check all the electrical connections, ensuring that the screws
and nuts are well secured;
4- Visually check the state of all the components: replace any
deteriorated components;
5- Put back the casing, tightening the side screws.
7.3- PREVENTIVE MAINTENANCE OF THE
50
ENGLISH
THOR 103
COD. 6909500060
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
2
;